Support - User contributions [en]

TP-Link TD-W9970 Configuration

2017-08-29T13:55:42Z

Fw309: /* Settings for VDSL */

[[File:TD-W9970_front.jpg|thumb|right|300px|The TP-Link TD-W9970 Modem Front]]
[[File:TD-W9970_back.jpg|thumb|right|300px|The TP-Link TD-W9970 Modem Back]]
The TP-Link TD-W9970 is for use on any service on networks using Bells' DSL infrastructure. NCF sells these modems to all members.

This is the procedure NCF uses to configure a TP-Link TD-W9970 modem out of the box or after a factory reset. To learn more about configuring your particular modem, consult the [[Modem manuals (DSL)|manual]].

== Configure router for Dual-Mode ADSL/VDSL operation==
Your router can support both ADSL and VDSL modes. If necessary, you could switch between ADSL and VDSL plans without having to buy a new router or even reconfigure your existing one.

===Settings for VDSL===
We will start with the mode used for VDSL connections. These include the following NCF DSL Plans:
* Freedom 10-7/Unl
* Freedom 15-10/Unl
* Freedom 25/Unl
* Freedom 50/Unl

=== Quick Setup ===
NOTE: If the modem is brand new, "user name: admin" and "password: admin" will gain access. If the modem is not new, it is recommended to reset the modem to the factory defaults by holding down the Reset/Wi-Fi button for 6 to 9 seconds and then do step 1.

1. Once you access the modem from your [[browser]] at http://192.168.1.1 and login (user name: admin and password: admin), click the link high-lighted in red (Quick Setup).

[[file:Td-w9970_setup1.png|800px|Getting started]]

'''Region: Canada'''
# Time Zone to '''(GMT-05:00) Eastern Time (US & Canada)'''
# Click '''Next'''

[[file:Td-w9970_setup2.png|800px|Step2]]

'''Quick Setup – Auto Detection'''
# Click on '''No, I want...'''
# Click '''Next'''

[[file:Td-w9970_setup3.png|800px|Step3]]

'''Quick Setup – DSL'''
# ISP: '''Other'''
# L2 Interface Type: '''VDSL'''
# Enable VLAN ID: '''checked'''
# VLAN: '''35'''
# Connection Type: '''PPPoE'''
# Click '''Next'''

[[file:Td-w9970_setup4.png|800px|Step4]]

'''Quick Setup - PPPoE'''
# User name: '''ab123@ncf.ca''' (where ab123 is your NCF ID)
# Password: '''••••••••''' (where •••••••• is your NCF DSL Password)
# Confirm password: '''••••••••'''
# Click '''Next'''

[[file:Td-w9970_setup5.png|800px|Step5]]

'''Quick Setup – 3G/4G'''
# Click '''Next'''

[[file:Td-w9970_setup6.png|800px|Step6]]

'''Quick Setup – Wireless'''
# Wireless: '''Enable'''
# Wireless Network Name (SSID): '''NCF_xxxx''' (where xxxx are the last 4 digits of the modem serial number)
# Channel: '''Auto'''
# Mode: '''11bgn mixed'''
# Security: '''WPA/WPA2'''
# Password: '''DSL Password'''
# Click '''Next'''

[[file:Td-w9970_setup7.png|800px|Step7]]

'''Quick Setup – Confirm'''
# Verify all setting are as entered
# Click '''Next'''

[[file:Td-w9970_setup8.png|800px|Step8]]

'''Quick Setup – Complete'''
# Click Finish

'''Stay logged-in'''
# Click '''Network''' (left-hand menu, 4th link from top)
#Click '''WAN Settings'''

'''Network – WAN Settings'''
# Click on '''Action: Edit''' (entry with pppoe_ptm_xx_x_x, right-hand side of table)

'''Network – WAN Settings'''
# WAN Service Setup, enter...
# Enable IPv6: '''Select'''
# Click '''Advance'''
# Enable SPI Firewall: '''selected'''
# Enable IGMP Proxy: '''un-select'''
# Click '''Save'''

=== Add Settings for ADSL ===
Moving on now to add settings for ADSL.
ADSL is required for the following NCF DSL Plans:
* Freedom 6/300
* Freedom 7/300
* Freedom 15-1/300

'''Stay logged-in'''
# Click '''Network''' (left-hand menu, 4th link from top)
# Click '''WAN Settings'''

'''Network – WAN Settings – DSL WAN Interface'''
# Click on '''Action: Delete''' (1st entry, right-hand side of table)
# Click '''Add''' button

[[file:Td-w9970_setup9.png|800px|Adding ADSL2+ WAN Config 1/2]]

'''WAN Service Setup, enter...'''
# DSL Modulation Type: '''ADSL'''
# ATM Configuration: '''VPI/VCI = 0/35'''
# Connection Type: '''PPPoE'''
# User name: '''ab123@ncf.ca''' (where ab123 is your NCF ID)
# Password: '''••••••••''' (where •••••••• is your NCF DSL Password)
# Confirm password: '''••••••••'''
# Connection Mode: select '''Always on'''
# Authentication Type: select '''AUTO_AUTH'''
# Enable IPv4: '''selected'''
# Default Gateway: select '''Current Connection'''
# Enable IPv6: '''select'''
# Click '''Advance'''
# Enable SPI Firewall: '''selected'''
# Enable IGMP Proxy: '''un-select'''
# Set DNS server manually: '''selected'''
# DNS Server: '''8.8.8.8'''
# Secondary DNS Server: '''134.117.136.91'''
# Click '''Save'''

[[file:Td-w9970_setup10.png|800px|Adding ADSL2+ WAN Config 2/2]]

== Additional Settings ==

'''UPnP'''
# Click on '''Forwarding''' (left-hand menu, near the middle)
# UPnP: '''de-select'''

'''Time Settings'''
# Click on '''System Tools''' (left-hand menu, towards the bottom)
# Select '''Time Settings'''
# Time Zone: '''(GMT-05:00) Eastern Time (US & Canada)'''
# NTP Server 1: '''time.nrc.ca'''
# Enable DST: '''checked'''
# Modify DST Start: '''2nd Sunday in March'''
# Modify DST End: '''1st Sunday in November'''
# Click '''Save'''

'''Manage Control'''
# Click on '''System Tools''' (left-hand menu, towards the bottom)
# Select '''Manage Control'''
# For the user admin we use the member's '''DSL Password''' – user name & password should not exceed 15 characters
# Enter it once and again below to confirm
# Ensure ICMP (Ping) is set to '''Local only''' (default setting)
# Click '''Save'''

'''CWMP Settings'''
# Click on '''System Tools''' (left-hand menu, towards the bottom)
# Select '''CWMP Settings'''
# Ensure that CWMP is '''de-selected''' (default setting)
# Ensure that Inform is '''de-selected''' (default setting)
# Click '''Save'''

== Configure as bridge ==
Do this only if you prefer to use your own external router rather than the one built into your TP-Link unit.

# Connect power and turn on the modem with the button on the back.
# Connect an Ethernet LAN cable to one of the yellow rear ports
# In the browser's address bar, enter the IP address for the modem interface page: 192.168.1.1
# If the modem is fresh from the factory, use the default user name and password to gain access
##'''user:''' admin
##'''password:''' admin

If the modem was previously configured for someone, the password would be the previous user's [[DSL password]]. If it is unknown then do a reset to factory default, press the reset/Wi-Fi button on the back. Hold for 6 to 9 seconds to reset. The user name and password will now be as above.

# Click on Quick Setup.

See screenshots below:

'''Quick Setup – DSL'''
# ISP: '''Other'''
# L2 Interface Type: '''VDSL'''
# Enable VLAN ID: '''checked'''
# VLAN: '''35'''
# Connection Type: '''Bridge'''
# Click '''Next'''

[[File:Td-w9970_bridge1.png|800px|Configuring for Bridge Mode 1/4]]

'''Quick Setup – Wireless'''
# Wireless: '''Disable'''
# Click '''Next'''

[[File:Td-w9970_bridge4.png|800px|Configuring for Bridge Mode 4/4]]

'''Quick Setup – Confirm'''
# Verify all setting are as entered
# Click '''Next'''

[[File:Td-w9970_bridge2.png|800px|Configuring for Bridge Mode 2/4]]

'''Stay logged-in'''
# Click '''Network''' (left-hand menu, 4th link from top)
# Click '''WAN Settings'''

'''Network – WAN Settings – WAN Settings'''
# DSL Modulation Type: select '''ADSL'''
# ATM Configuration, enter...
# VPI: '''0'''
# VCI: '''35'''

[[File:Td-w9970_bridge3.png|800px|Configuring for Bridge Mode 3/3]]

# WAN Service Setup, enter...
# Connection Type: '''Bridge'''
# Click '''Save'''

== Modem Password Setup ==
Click on the "System Tools" link on the LH side of the page, then "Manage Control". Change the modem access password to NCF standard.

[[file:Td-w9970_setup11.png|800px|Setting Admin Password]]

== Configuring Time Zone ==
Click on the "System Tools" link on the LH side of the page, then "Time Settings". Set the timezone to Eastern Standard Time, enable DST (Daylight Savings Time), and set the NTP server to the NRC clocks (time.nrc.ca).

[[file:Td-w9970_setup12.png|800px|Configuring Time Settings]]

==Turn on the Firewall==
*Click 'Firewall' in the left column
*Select 'Enable Firewall'

== See also ==
*[http://www.ncf.ca/ncf/dsl/modem/TD-W9970_V1_UG.pdf TP-Link TD-W9970 manual]

*[[About DSL modem lights - TP-Link modems]]
*[[Dynamic DNS]]
*[[Modem Configuration (DSL)]] - for a complete list of instructions for all NCF modems
*[[Modem manuals (DSL)]]
*[[Port forwarding]]
[[Category: DSL]]

SmartRG SR505N Configuration

2017-08-17T19:17:43Z

Fw309: /* Add Settings for ADSL Mode */

[[File:sr505N-front.jpg|thumb|right|300px|The SmartRG SR505N Modem Front]]
[[File:sr505n_back.jpg|thumb|right|300px|The SmartRG SR505N Modem Back]]
The SmartRG SR505N is for use any DSL service over Bells' DSL infrastructure. NCF started selling these modems from September 2014 to members.

This is the procedure NCF uses to configure a SmartRG SR505N modem out of the box or after a factory reset. To learn more about configuring your particular modem, consult the [[Modem manuals (DSL)|manual]].

== Configure router for Dual Mode ADSL/VDSL operation==
Your router can support both ADSL mode and VDSL mode. If necessary, you could switch between ADSL plans and VDSL plans without having to buy a new router or even reconfigure your existing one.

===Settings for VDSL===
We will start with the mode used for VDSL connections. These include the following NCF DSL Plans:
* Freedom 10/7, Unlimited
* Freedom 15/10, Unlimited
* Freedom 25/10, Unlimited
* Freedom 50/10, Unlimited

=== Getting Started ===
NOTE: If the modem is brand new, "user name: admin and password admin" will gain access. If the modem is not new, it is recommended to reset the modem to the factory defaults by holding down the reset button with a paper clip for ~10 seconds and then do step 1.

1. Once you access the modem browser at 192.168.1.1 and login (user name: admin and password admin), click the link high-lighted in red.

[[file:smartrg_1.jpg|Getting started]]

=== Advanced Setup ===
2. Click on the "Advanced Setup" link on the LH side of the page.
[[file:smartrg_2.jpg|Advanced Setup]]

=== WAN Service ===
3. Click on the "WAN Service" link under "Advanced Setup" and then click on the "Edit" link highlighted in red.
[[file:smartrg_3.jpg|WAN Service]]

=== Username Setup ===
4. On the 'PPP Username and Password' page, fill the username and password details in the field highlighted in red. Be sure to scroll to the bottom of this page checking that "Enable Firewall" and "Enable NAT" are all checked. Click "Next".
[[file:smartrg_4.jpg|960px|PPPOE set up]]
[[file:Smartrg_505n_vdsl_NAT_SIP_005.png]]

=== PPPoE config save ===


Click on "Next"
[[File:Smartrg_505n_adsl09.png|765px|none|Configuring ADSL2+ 9/11]]

Click on "Next"
[[File:Smartrg_505n_adsl10.png|1000px|Configuring ADSL2+ 10/11]]

Click on "Apply/Save".
[[file:smartrg_5.jpg|PPoE config save]]














=== Add Settings for ADSL Mode===
Moving on now to add settings for ADSL mode.
ADSL plans include the following NCF DSL Plans:
* Freedom 6/0.8, Unlimited
* Freedom 7/1, Unlimited
* Freedom 10/1, Unlimited
* Freedom 15/1, Unlimited

#Click on "Advanced Setup"
#Click on "Layer2 Interface"
#Click on "ATM Interface"
#Click on "Add"


[[File:smartrg_505n_adsl03.png|1000px|Configuring ADSL2+ 3/11]]

#Ensure that VPI is 0 and that VCI is 35.
#Ensure that Fast and Interleaved are selected under DSL Latency.
# For everything else, use the defaults.
#Scroll to the bottom of the page, and click "Apply/Save".
[[File:smartrgpic1.png|1000px|Configuring ADSL2+ 4/11]]

# Click "Advanced Setup"
#Click "WAN Service"
#Click "Add"
[[File:Smartrg_505n_adsl05.png|1000px|Configuring ADSL2+ 5/11]]

#From the drop-down box, select "atm0/(4_0_35)"
#Click "Next"
[[File:Smartrg_505n_adsl06.png|1000px|Configuring ADSL2+ 6/11]]

#Ensure "PPPoE" is the active choice.
#Ensure "Service description" is as shown.
#Click "Next".
[[File:Smartrg_505n_adsl07.png|1000px|Configuring ADSL2+ 7/11]]

Ensure "Enable Firewall", "Enable NAT" and "Enable SIP" are checked. Scroll to the bottom of the page and click "Next".
[[File:Smartrg_505n_adsl08.png|1000px|Configuring ADSL2+ 8/11]]

Click on "Next"
[[File:Smartrg_505n_adsl09.png|1000px|Configuring ADSL2+ 9/11]]

Click on "Next"
[[File:Smartrg_505n_adsl10.png|1000px|Configuring ADSL2+ 10/11]]

Click on "Apply/Save"
[[File:Smartrg_505n_adsl11.png|1000px|Configuring ADSL2+ 11/11]]

'''You are done adding the ADSL settings. Now, skip ahead to [[#Wireless_Configuration|Wireless Configuration]].'''

== Configure as bridge ==
Do this only if you prefer to use your own external router rather than the one built into your SmartRG unit.

# Connect power and turn on the modem with the button on the back.
# Connect an Ethernet LAN cable to one of the yellow rear ports
# In the browser's address bar, enter the IP address for the modem interface page: 192.168.1.1
# If the modem is fresh from the factory, use the default user name and password to gain access
##'''user:''' admin
##'''password:''' admin

If the modem was previously configured for someone, the password would be the previous user's [[DSL password]]. If it is unknown then do a reset to factory default, using a paper-clip in the reset hole on the back. Hold for 6 to 9 seconds to reset. The user name and password will now be as above.

# Click on Advanced Setup and WAN Service and click on Add
# The defaults are fine; click on Next.
# Click on Bridging and ensure the 802.1P and 802.1Q are set to 0 and 35, then click on Next.
# Click on Apply/Save
# Done!

See screenshots below:

[[File:smartrg_505n_bridge_1.png|Configuring for Bridge Mode 1/5]]
[[File:smartrg_505n_bridge_2.png|Configuring for Bridge Mode 2/5]]
[[File:smartrg_505n_bridge_3.png|Configuring for Bridge Mode 3/5]]
[[File:smartrg_505n_bridge_4.png|Configuring for Bridge Mode 4/5]]
[[File:smartrg_505n_bridge_5.png|Configuring for Bridge Mode 5/5]]

== Wireless Configuration ==
Continuing now to set the '''Wireless''' configuration
# Ensure '''Enable Wireless''' is checked
# The '''SSID''' is set to NCF plus a random number (NCF uses the last 4 digits of the serial number), such as '''NCF_1234'''. It is recommended you not use your first or last name, or street address as this information is broadcast and other people in your area will be able to associate the signal with which home it is coming from.
# Click on '''Apply/Save''' at the bottom.
[[File:Smartrg_505n_adsl12.png|1000px|Configuring Wireless 1/2]]

# Click on '''Security''' on the left.
# Set the '''Network Authentication''' to Mixed WPA2/WPA-PSK
# Uncheck '''Use base MAC address as WPA/WAPI passphrase
# Set the '''WPA/WAPI passphrase''' to be your DSL-Password
# Click '''Apply/save'''.
[[File:Smartrg_505n_adsl13.png|1000px|Configuring Wireless 2/2]]

== Password protect the Admin Role ==
# Click on '''Management''' on the left. Below it other options appear.
# Select '''Access Control'''
# Select '''Passwords'''
# Enter '''admin''' for the User Name
# Enter '''admin''' for the Old Password
# For the New Password use your DSL-Password or another strong password.
# Enter it once and again below to confirm
# Save the changes with '''Apply/Save'''

Click on "Device Info". A pop-up log-in screen appears, and asks for sign-in. Use the User-ID '''admin''' and the DSL-Password just set. Return to the same configure page you were just at.

[[File:Smartrg_505n_adsl14.png|1000px|Setting Admin Password]]

== See also ==
*[http://www.ncf.ca/ncf/dsl/modem/SmartRG_3xx-5xx_Gateway_User_Manual.pdf SmartRG SR505N modem manual]
*[https://www.ncf.ca/ncf/support/w/images/f/f8/Modem_Info_Pages_-_SmartRG_505n_v1.0.pdf NCF SmartRG SR505N modem instruction sheet]
*[[About DSL modem lights - SmartRG modems]]
*[[Dynamic DNS]]
*[[Modem Configuration (DSL)]] - for a complete list of instructions for all NCF modems
*[[Port forwarding]]
[[Category: DSL]]

SmartRG SR505N Configuration

2017-08-17T19:17:08Z

Fw309: /* Add Settings for ADSL Mode */

[[File:sr505N-front.jpg|thumb|right|300px|The SmartRG SR505N Modem Front]]
[[File:sr505n_back.jpg|thumb|right|300px|The SmartRG SR505N Modem Back]]
The SmartRG SR505N is for use any DSL service over Bells' DSL infrastructure. NCF started selling these modems from September 2014 to members.

This is the procedure NCF uses to configure a SmartRG SR505N modem out of the box or after a factory reset. To learn more about configuring your particular modem, consult the [[Modem manuals (DSL)|manual]].

== Configure router for Dual Mode ADSL/VDSL operation==
Your router can support both ADSL mode and VDSL mode. If necessary, you could switch between ADSL plans and VDSL plans without having to buy a new router or even reconfigure your existing one.

===Settings for VDSL===
We will start with the mode used for VDSL connections. These include the following NCF DSL Plans:
* Freedom 10/7, Unlimited
* Freedom 15/10, Unlimited
* Freedom 25/10, Unlimited
* Freedom 50/10, Unlimited

=== Getting Started ===
NOTE: If the modem is brand new, "user name: admin and password admin" will gain access. If the modem is not new, it is recommended to reset the modem to the factory defaults by holding down the reset button with a paper clip for ~10 seconds and then do step 1.

1. Once you access the modem browser at 192.168.1.1 and login (user name: admin and password admin), click the link high-lighted in red.

[[file:smartrg_1.jpg|Getting started]]

=== Advanced Setup ===
2. Click on the "Advanced Setup" link on the LH side of the page.
[[file:smartrg_2.jpg|Advanced Setup]]

=== WAN Service ===
3. Click on the "WAN Service" link under "Advanced Setup" and then click on the "Edit" link highlighted in red.
[[file:smartrg_3.jpg|WAN Service]]

=== Username Setup ===
4. On the 'PPP Username and Password' page, fill the username and password details in the field highlighted in red. Be sure to scroll to the bottom of this page checking that "Enable Firewall" and "Enable NAT" are all checked. Click "Next".
[[file:smartrg_4.jpg|960px|PPPOE set up]]
[[file:Smartrg_505n_vdsl_NAT_SIP_005.png]]

=== PPPoE config save ===


Click on "Next"
[[File:Smartrg_505n_adsl09.png|765px|none|Configuring ADSL2+ 9/11]]

Click on "Next"
[[File:Smartrg_505n_adsl10.png|1000px|Configuring ADSL2+ 10/11]]

Click on "Apply/Save".
[[file:smartrg_5.jpg|PPoE config save]]














=== Add Settings for ADSL Mode===
Moving on now to add settings for ADSL mode.
ADSL plans include the following NCF DSL Plans:
* Freedom 6/0.8, Unlimited
* Freedom 7/1, Unlimited
* Freedom 10/1, Unlimited
* Freedom 15/1, Unlimited

#Click on "Advanced Setup"
#Click on "Layer2 Interface"
#Click on "ATM Interface"
#Click on "Add"


[[File:smartrg_505n_adsl03.png|1000px|Configuring ADSL2+ 3/11]]

#Ensure that VPI is 0 and that VCI is 35.
#Ensure that Fast and Interleaved are selected under DSL Latency.
# For everything else, use the defaults.
#Scroll to the bottom of the page, and click "Next".
[[File:smartrgpic1.png|1000px|Configuring ADSL2+ 4/11]]

# Click "Advanced Setup"
#Click "WAN Service"
#Click "Add"
[[File:Smartrg_505n_adsl05.png|1000px|Configuring ADSL2+ 5/11]]

#From the drop-down box, select "atm0/(4_0_35)"
#Click "Next"
[[File:Smartrg_505n_adsl06.png|1000px|Configuring ADSL2+ 6/11]]

#Ensure "PPPoE" is the active choice.
#Ensure "Service description" is as shown.
#Click "Next".
[[File:Smartrg_505n_adsl07.png|1000px|Configuring ADSL2+ 7/11]]

Ensure "Enable Firewall", "Enable NAT" and "Enable SIP" are checked. Scroll to the bottom of the page and click "Next".
[[File:Smartrg_505n_adsl08.png|1000px|Configuring ADSL2+ 8/11]]

Click on "Next"
[[File:Smartrg_505n_adsl09.png|1000px|Configuring ADSL2+ 9/11]]

Click on "Next"
[[File:Smartrg_505n_adsl10.png|1000px|Configuring ADSL2+ 10/11]]

Click on "Apply/Save"
[[File:Smartrg_505n_adsl11.png|1000px|Configuring ADSL2+ 11/11]]

'''You are done adding the ADSL settings. Now, skip ahead to [[#Wireless_Configuration|Wireless Configuration]].'''

== Configure as bridge ==
Do this only if you prefer to use your own external router rather than the one built into your SmartRG unit.

# Connect power and turn on the modem with the button on the back.
# Connect an Ethernet LAN cable to one of the yellow rear ports
# In the browser's address bar, enter the IP address for the modem interface page: 192.168.1.1
# If the modem is fresh from the factory, use the default user name and password to gain access
##'''user:''' admin
##'''password:''' admin

If the modem was previously configured for someone, the password would be the previous user's [[DSL password]]. If it is unknown then do a reset to factory default, using a paper-clip in the reset hole on the back. Hold for 6 to 9 seconds to reset. The user name and password will now be as above.

# Click on Advanced Setup and WAN Service and click on Add
# The defaults are fine; click on Next.
# Click on Bridging and ensure the 802.1P and 802.1Q are set to 0 and 35, then click on Next.
# Click on Apply/Save
# Done!

See screenshots below:

[[File:smartrg_505n_bridge_1.png|Configuring for Bridge Mode 1/5]]
[[File:smartrg_505n_bridge_2.png|Configuring for Bridge Mode 2/5]]
[[File:smartrg_505n_bridge_3.png|Configuring for Bridge Mode 3/5]]
[[File:smartrg_505n_bridge_4.png|Configuring for Bridge Mode 4/5]]
[[File:smartrg_505n_bridge_5.png|Configuring for Bridge Mode 5/5]]

== Wireless Configuration ==
Continuing now to set the '''Wireless''' configuration
# Ensure '''Enable Wireless''' is checked
# The '''SSID''' is set to NCF plus a random number (NCF uses the last 4 digits of the serial number), such as '''NCF_1234'''. It is recommended you not use your first or last name, or street address as this information is broadcast and other people in your area will be able to associate the signal with which home it is coming from.
# Click on '''Apply/Save''' at the bottom.
[[File:Smartrg_505n_adsl12.png|1000px|Configuring Wireless 1/2]]

# Click on '''Security''' on the left.
# Set the '''Network Authentication''' to Mixed WPA2/WPA-PSK
# Uncheck '''Use base MAC address as WPA/WAPI passphrase
# Set the '''WPA/WAPI passphrase''' to be your DSL-Password
# Click '''Apply/save'''.
[[File:Smartrg_505n_adsl13.png|1000px|Configuring Wireless 2/2]]

== Password protect the Admin Role ==
# Click on '''Management''' on the left. Below it other options appear.
# Select '''Access Control'''
# Select '''Passwords'''
# Enter '''admin''' for the User Name
# Enter '''admin''' for the Old Password
# For the New Password use your DSL-Password or another strong password.
# Enter it once and again below to confirm
# Save the changes with '''Apply/Save'''

Click on "Device Info". A pop-up log-in screen appears, and asks for sign-in. Use the User-ID '''admin''' and the DSL-Password just set. Return to the same configure page you were just at.

[[File:Smartrg_505n_adsl14.png|1000px|Setting Admin Password]]

== See also ==
*[http://www.ncf.ca/ncf/dsl/modem/SmartRG_3xx-5xx_Gateway_User_Manual.pdf SmartRG SR505N modem manual]
*[https://www.ncf.ca/ncf/support/w/images/f/f8/Modem_Info_Pages_-_SmartRG_505n_v1.0.pdf NCF SmartRG SR505N modem instruction sheet]
*[[About DSL modem lights - SmartRG modems]]
*[[Dynamic DNS]]
*[[Modem Configuration (DSL)]] - for a complete list of instructions for all NCF modems
*[[Port forwarding]]
[[Category: DSL]]

SmartRG SR505N Configuration

2017-08-17T19:16:35Z

Fw309: /* Add Settings for ADSL Mode */

[[File:sr505N-front.jpg|thumb|right|300px|The SmartRG SR505N Modem Front]]
[[File:sr505n_back.jpg|thumb|right|300px|The SmartRG SR505N Modem Back]]
The SmartRG SR505N is for use any DSL service over Bells' DSL infrastructure. NCF started selling these modems from September 2014 to members.

This is the procedure NCF uses to configure a SmartRG SR505N modem out of the box or after a factory reset. To learn more about configuring your particular modem, consult the [[Modem manuals (DSL)|manual]].

== Configure router for Dual Mode ADSL/VDSL operation==
Your router can support both ADSL mode and VDSL mode. If necessary, you could switch between ADSL plans and VDSL plans without having to buy a new router or even reconfigure your existing one.

===Settings for VDSL===
We will start with the mode used for VDSL connections. These include the following NCF DSL Plans:
* Freedom 10/7, Unlimited
* Freedom 15/10, Unlimited
* Freedom 25/10, Unlimited
* Freedom 50/10, Unlimited

=== Getting Started ===
NOTE: If the modem is brand new, "user name: admin and password admin" will gain access. If the modem is not new, it is recommended to reset the modem to the factory defaults by holding down the reset button with a paper clip for ~10 seconds and then do step 1.

1. Once you access the modem browser at 192.168.1.1 and login (user name: admin and password admin), click the link high-lighted in red.

[[file:smartrg_1.jpg|Getting started]]

=== Advanced Setup ===
2. Click on the "Advanced Setup" link on the LH side of the page.
[[file:smartrg_2.jpg|Advanced Setup]]

=== WAN Service ===
3. Click on the "WAN Service" link under "Advanced Setup" and then click on the "Edit" link highlighted in red.
[[file:smartrg_3.jpg|WAN Service]]

=== Username Setup ===
4. On the 'PPP Username and Password' page, fill the username and password details in the field highlighted in red. Be sure to scroll to the bottom of this page checking that "Enable Firewall" and "Enable NAT" are all checked. Click "Next".
[[file:smartrg_4.jpg|960px|PPPOE set up]]
[[file:Smartrg_505n_vdsl_NAT_SIP_005.png]]

=== PPPoE config save ===


Click on "Next"
[[File:Smartrg_505n_adsl09.png|765px|none|Configuring ADSL2+ 9/11]]

Click on "Next"
[[File:Smartrg_505n_adsl10.png|1000px|Configuring ADSL2+ 10/11]]

Click on "Apply/Save".
[[file:smartrg_5.jpg|PPoE config save]]














=== Add Settings for ADSL Mode===
Moving on now to add settings for ADSL mode.
ADSL plans include the following NCF DSL Plans:
* Freedom 6/0.8, Unlimited
* Freedom 7/1, Unlimited
* Freedom 10/1, Unlimited
* Freedom 15/1, Unlimited

#Click on "Advanced Setup"
#Click on "Layer2 Interface"
#Click on "ATM Interface"
#Click on "Add"


[[File:smartrg_505n_adsl03.png|1000px|Configuring ADSL2+ 3/11]]

#Ensure that VPI is 0 and that VCI is 35.
#Ensure that Fast and Interleaved are selected.
# For everything else, use the defaults.
#Scroll to the bottom of the page, and click "Next".
[[File:smartrgpic1.png|1000px|Configuring ADSL2+ 4/11]]

# Click "Advanced Setup"
#Click "WAN Service"
#Click "Add"
[[File:Smartrg_505n_adsl05.png|1000px|Configuring ADSL2+ 5/11]]

#From the drop-down box, select "atm0/(4_0_35)"
#Click "Next"
[[File:Smartrg_505n_adsl06.png|1000px|Configuring ADSL2+ 6/11]]

#Ensure "PPPoE" is the active choice.
#Ensure "Service description" is as shown.
#Click "Next".
[[File:Smartrg_505n_adsl07.png|1000px|Configuring ADSL2+ 7/11]]

Ensure "Enable Firewall", "Enable NAT" and "Enable SIP" are checked. Scroll to the bottom of the page and click "Next".
[[File:Smartrg_505n_adsl08.png|1000px|Configuring ADSL2+ 8/11]]

Click on "Next"
[[File:Smartrg_505n_adsl09.png|1000px|Configuring ADSL2+ 9/11]]

Click on "Next"
[[File:Smartrg_505n_adsl10.png|1000px|Configuring ADSL2+ 10/11]]

Click on "Apply/Save"
[[File:Smartrg_505n_adsl11.png|1000px|Configuring ADSL2+ 11/11]]

'''You are done adding the ADSL settings. Now, skip ahead to [[#Wireless_Configuration|Wireless Configuration]].'''

== Configure as bridge ==
Do this only if you prefer to use your own external router rather than the one built into your SmartRG unit.

# Connect power and turn on the modem with the button on the back.
# Connect an Ethernet LAN cable to one of the yellow rear ports
# In the browser's address bar, enter the IP address for the modem interface page: 192.168.1.1
# If the modem is fresh from the factory, use the default user name and password to gain access
##'''user:''' admin
##'''password:''' admin

If the modem was previously configured for someone, the password would be the previous user's [[DSL password]]. If it is unknown then do a reset to factory default, using a paper-clip in the reset hole on the back. Hold for 6 to 9 seconds to reset. The user name and password will now be as above.

# Click on Advanced Setup and WAN Service and click on Add
# The defaults are fine; click on Next.
# Click on Bridging and ensure the 802.1P and 802.1Q are set to 0 and 35, then click on Next.
# Click on Apply/Save
# Done!

See screenshots below:

[[File:smartrg_505n_bridge_1.png|Configuring for Bridge Mode 1/5]]
[[File:smartrg_505n_bridge_2.png|Configuring for Bridge Mode 2/5]]
[[File:smartrg_505n_bridge_3.png|Configuring for Bridge Mode 3/5]]
[[File:smartrg_505n_bridge_4.png|Configuring for Bridge Mode 4/5]]
[[File:smartrg_505n_bridge_5.png|Configuring for Bridge Mode 5/5]]

== Wireless Configuration ==
Continuing now to set the '''Wireless''' configuration
# Ensure '''Enable Wireless''' is checked
# The '''SSID''' is set to NCF plus a random number (NCF uses the last 4 digits of the serial number), such as '''NCF_1234'''. It is recommended you not use your first or last name, or street address as this information is broadcast and other people in your area will be able to associate the signal with which home it is coming from.
# Click on '''Apply/Save''' at the bottom.
[[File:Smartrg_505n_adsl12.png|1000px|Configuring Wireless 1/2]]

# Click on '''Security''' on the left.
# Set the '''Network Authentication''' to Mixed WPA2/WPA-PSK
# Uncheck '''Use base MAC address as WPA/WAPI passphrase
# Set the '''WPA/WAPI passphrase''' to be your DSL-Password
# Click '''Apply/save'''.
[[File:Smartrg_505n_adsl13.png|1000px|Configuring Wireless 2/2]]

== Password protect the Admin Role ==
# Click on '''Management''' on the left. Below it other options appear.
# Select '''Access Control'''
# Select '''Passwords'''
# Enter '''admin''' for the User Name
# Enter '''admin''' for the Old Password
# For the New Password use your DSL-Password or another strong password.
# Enter it once and again below to confirm
# Save the changes with '''Apply/Save'''

Click on "Device Info". A pop-up log-in screen appears, and asks for sign-in. Use the User-ID '''admin''' and the DSL-Password just set. Return to the same configure page you were just at.

[[File:Smartrg_505n_adsl14.png|1000px|Setting Admin Password]]

== See also ==
*[http://www.ncf.ca/ncf/dsl/modem/SmartRG_3xx-5xx_Gateway_User_Manual.pdf SmartRG SR505N modem manual]
*[https://www.ncf.ca/ncf/support/w/images/f/f8/Modem_Info_Pages_-_SmartRG_505n_v1.0.pdf NCF SmartRG SR505N modem instruction sheet]
*[[About DSL modem lights - SmartRG modems]]
*[[Dynamic DNS]]
*[[Modem Configuration (DSL)]] - for a complete list of instructions for all NCF modems
*[[Port forwarding]]
[[Category: DSL]]

File:Smartrgpic.png

2017-08-17T19:13:24Z

Fw309:

SmartRG SR505N Configuration

2017-08-17T19:13:13Z

Fw309: /* Add Settings for ADSL Mode */

[[File:sr505N-front.jpg|thumb|right|300px|The SmartRG SR505N Modem Front]]
[[File:sr505n_back.jpg|thumb|right|300px|The SmartRG SR505N Modem Back]]
The SmartRG SR505N is for use any DSL service over Bells' DSL infrastructure. NCF started selling these modems from September 2014 to members.

This is the procedure NCF uses to configure a SmartRG SR505N modem out of the box or after a factory reset. To learn more about configuring your particular modem, consult the [[Modem manuals (DSL)|manual]].

== Configure router for Dual Mode ADSL/VDSL operation==
Your router can support both ADSL mode and VDSL mode. If necessary, you could switch between ADSL plans and VDSL plans without having to buy a new router or even reconfigure your existing one.

===Settings for VDSL===
We will start with the mode used for VDSL connections. These include the following NCF DSL Plans:
* Freedom 10/7, Unlimited
* Freedom 15/10, Unlimited
* Freedom 25/10, Unlimited
* Freedom 50/10, Unlimited

=== Getting Started ===
NOTE: If the modem is brand new, "user name: admin and password admin" will gain access. If the modem is not new, it is recommended to reset the modem to the factory defaults by holding down the reset button with a paper clip for ~10 seconds and then do step 1.

1. Once you access the modem browser at 192.168.1.1 and login (user name: admin and password admin), click the link high-lighted in red.

[[file:smartrg_1.jpg|Getting started]]

=== Advanced Setup ===
2. Click on the "Advanced Setup" link on the LH side of the page.
[[file:smartrg_2.jpg|Advanced Setup]]

=== WAN Service ===
3. Click on the "WAN Service" link under "Advanced Setup" and then click on the "Edit" link highlighted in red.
[[file:smartrg_3.jpg|WAN Service]]

=== Username Setup ===
4. On the 'PPP Username and Password' page, fill the username and password details in the field highlighted in red. Be sure to scroll to the bottom of this page checking that "Enable Firewall" and "Enable NAT" are all checked. Click "Next".
[[file:smartrg_4.jpg|960px|PPPOE set up]]
[[file:Smartrg_505n_vdsl_NAT_SIP_005.png]]

=== PPPoE config save ===


Click on "Next"
[[File:Smartrg_505n_adsl09.png|765px|none|Configuring ADSL2+ 9/11]]

Click on "Next"
[[File:Smartrg_505n_adsl10.png|1000px|Configuring ADSL2+ 10/11]]

Click on "Apply/Save".
[[file:smartrg_5.jpg|PPoE config save]]














=== Add Settings for ADSL Mode===
Moving on now to add settings for ADSL mode.
ADSL plans include the following NCF DSL Plans:
* Freedom 6/0.8, Unlimited
* Freedom 7/1, Unlimited
* Freedom 10/1, Unlimited
* Freedom 15/1, Unlimited

#Click on "Advanced Setup"
#Click on "Layer2 Interface"
#Click on "ATM Interface"
#Click on "Add"


[[File:smartrg_505n_adsl03.png|1000px|Configuring ADSL2+ 3/11]]

#Ensure that VPI is 0 and that VCI is 35.
#Ensure that Fast and Interleaved are selected.
# For everything else, use the defaults.
#Scroll to the bottom of the page, and click "Next".
[[File:smartrgpic.png|1000px|Configuring ADSL2+ 4/11]]

# Click "Advanced Setup"
#Click "WAN Service"
#Click "Add"
[[File:Smartrg_505n_adsl05.png|1000px|Configuring ADSL2+ 5/11]]

#From the drop-down box, select "atm0/(4_0_35)"
#Click "Next"
[[File:Smartrg_505n_adsl06.png|1000px|Configuring ADSL2+ 6/11]]

#Ensure "PPPoE" is the active choice.
#Ensure "Service description" is as shown.
#Click "Next".
[[File:Smartrg_505n_adsl07.png|1000px|Configuring ADSL2+ 7/11]]

Ensure "Enable Firewall", "Enable NAT" and "Enable SIP" are checked. Scroll to the bottom of the page and click "Next".
[[File:Smartrg_505n_adsl08.png|1000px|Configuring ADSL2+ 8/11]]

Click on "Next"
[[File:Smartrg_505n_adsl09.png|1000px|Configuring ADSL2+ 9/11]]

Click on "Next"
[[File:Smartrg_505n_adsl10.png|1000px|Configuring ADSL2+ 10/11]]

Click on "Apply/Save"
[[File:Smartrg_505n_adsl11.png|1000px|Configuring ADSL2+ 11/11]]

'''You are done adding the ADSL settings. Now, skip ahead to [[#Wireless_Configuration|Wireless Configuration]].'''

== Configure as bridge ==
Do this only if you prefer to use your own external router rather than the one built into your SmartRG unit.

# Connect power and turn on the modem with the button on the back.
# Connect an Ethernet LAN cable to one of the yellow rear ports
# In the browser's address bar, enter the IP address for the modem interface page: 192.168.1.1
# If the modem is fresh from the factory, use the default user name and password to gain access
##'''user:''' admin
##'''password:''' admin

If the modem was previously configured for someone, the password would be the previous user's [[DSL password]]. If it is unknown then do a reset to factory default, using a paper-clip in the reset hole on the back. Hold for 6 to 9 seconds to reset. The user name and password will now be as above.

# Click on Advanced Setup and WAN Service and click on Add
# The defaults are fine; click on Next.
# Click on Bridging and ensure the 802.1P and 802.1Q are set to 0 and 35, then click on Next.
# Click on Apply/Save
# Done!

See screenshots below:

[[File:smartrg_505n_bridge_1.png|Configuring for Bridge Mode 1/5]]
[[File:smartrg_505n_bridge_2.png|Configuring for Bridge Mode 2/5]]
[[File:smartrg_505n_bridge_3.png|Configuring for Bridge Mode 3/5]]
[[File:smartrg_505n_bridge_4.png|Configuring for Bridge Mode 4/5]]
[[File:smartrg_505n_bridge_5.png|Configuring for Bridge Mode 5/5]]

== Wireless Configuration ==
Continuing now to set the '''Wireless''' configuration
# Ensure '''Enable Wireless''' is checked
# The '''SSID''' is set to NCF plus a random number (NCF uses the last 4 digits of the serial number), such as '''NCF_1234'''. It is recommended you not use your first or last name, or street address as this information is broadcast and other people in your area will be able to associate the signal with which home it is coming from.
# Click on '''Apply/Save''' at the bottom.
[[File:Smartrg_505n_adsl12.png|1000px|Configuring Wireless 1/2]]

# Click on '''Security''' on the left.
# Set the '''Network Authentication''' to Mixed WPA2/WPA-PSK
# Uncheck '''Use base MAC address as WPA/WAPI passphrase
# Set the '''WPA/WAPI passphrase''' to be your DSL-Password
# Click '''Apply/save'''.
[[File:Smartrg_505n_adsl13.png|1000px|Configuring Wireless 2/2]]

== Password protect the Admin Role ==
# Click on '''Management''' on the left. Below it other options appear.
# Select '''Access Control'''
# Select '''Passwords'''
# Enter '''admin''' for the User Name
# Enter '''admin''' for the Old Password
# For the New Password use your DSL-Password or another strong password.
# Enter it once and again below to confirm
# Save the changes with '''Apply/Save'''

Click on "Device Info". A pop-up log-in screen appears, and asks for sign-in. Use the User-ID '''admin''' and the DSL-Password just set. Return to the same configure page you were just at.

[[File:Smartrg_505n_adsl14.png|1000px|Setting Admin Password]]

== See also ==
*[http://www.ncf.ca/ncf/dsl/modem/SmartRG_3xx-5xx_Gateway_User_Manual.pdf SmartRG SR505N modem manual]
*[https://www.ncf.ca/ncf/support/w/images/f/f8/Modem_Info_Pages_-_SmartRG_505n_v1.0.pdf NCF SmartRG SR505N modem instruction sheet]
*[[About DSL modem lights - SmartRG modems]]
*[[Dynamic DNS]]
*[[Modem Configuration (DSL)]] - for a complete list of instructions for all NCF modems
*[[Port forwarding]]
[[Category: DSL]]