https://help.ncf.ca/api.php?action=feedcontributions&user=Fx315&feedformat=atomSupport - User contributions [en]2024-03-29T09:51:23ZUser contributionsMediaWiki 1.36.4https://help.ncf.ca/index.php?title=SmartRG_SR505N_Configuration&diff=1897SmartRG SR505N Configuration2014-11-03T17:38:54Z<p>Fx315: /* Add Settings for ADSL Mode */</p>
<hr />
<div>[[File:sr505N-front.jpg|thumb|right|300px|The SmartRG SR505N Modem Front]]<br />
[[File:sr505n_back.jpg|thumb|right|300px|The SmartRG SR505N Modem Back]]<br />
This is the procedure NCF uses to configure a SmartRG SR505N modem out of the box or after a factory reset. To learn more about configuring your particular modem, consult the [[Modem manuals (DSL)|manual]].<br />
<br />
=== Configure router for Dual Mode ADSL/VDSL operation===<br />
Your router can support both ADSL mode and VDSL mode. If necessary, you could switch between ADSL plans and VDSL plans without having to buy a new router or even reconfigure your existing one.<br />
<br />
<br />
====Settings for VDSL====<br />
We'll start with the mode used for VDSL connections. These include the following NCF DSL Plans:<br />
* Freedom 15-10/300<br />
* Freedom 25/300<br />
* Freedom 50/300<br />
<br />
<br />
==== Getting Started ====<br />
NOTE: If the modem is brand new, "admin/admin" will be correct. If it's not new, it's recommended to reset the modem to factory defaults by holding down the reset button with a paper clip for 6 to 9 seconds and then do step 1.<br />
<br />
1. Once you access the modem browser at 191.168.1.1 and login ( admin/admin), click the link high-lighted in red.<br />
<br />
<br />
[[file:smartrg_1.jpg|Getting started]]<br />
<br />
==== Advanced Setup ====<br />
2. Click on the "Advanced Setup" link on the LH side of the page.<br />
[[file:smartrg_2.jpg|Advanced Setup]]<br />
<br />
==== WAN Service ====<br />
3. Click on the "WAN Service" link under "Advanced Setup" and then click on the "Edit" link highlighted in red.<br />
[[file:smartrg_3.jpg|WAN Service]]<br />
<br />
==== Username Setup ====<br />
4. On the 'PPP Username and Password' page, fill the username and password details in the field highlighted in red.<br />
Scroll to the bottom of this page - check that "Firewall" and "NAT" are enabled. Click "Next".<br />
[[file:smartrg_4.jpg|PPPOE set up]]<br />
<br />
==== PPPoE config save ====<br />
<!--5. There will be two more pages to scroll through and them you can finally "Save" these changes. At this point, the Internet light on the SmartRG should turn from red and eventually to green.--><br />
<br />
Click on "ppp0.1" and then "Next"<br />
[[File:smartrg_505n_adsl09.png|Configuring ADSL2+ 9/11]]<br />
Click on "ppp0.1" and then "Next"<br />
[[File:smartrg_505n_adsl10.png|Configuring ADSL2+ 10/11]]<br />
Click on "Apply/Save".<br />
[[file:smartrg_5.jpg|PPoE config save]]<br />
<br />
<!--==== Wireless Setup ====--><br />
<!--6. Click on the "Wireless" link on the RH side of the page.--><br />
<!--Change the SSID to the NCF standard name.--><br />
<!--Click on the "Security" subtab , store the NCF DSL password for the wi-fi password.--><br />
<br />
<!--====Modem Password Setup ====<br />
7. Click on the "Management " link on the RH side of the page. Click on the "Access"?? subtab and then the "Passwords" sub.sub tab. Change the modem access password to NCF standard.<br />
<br />
<br />
I need some more images to complete this - all in due time.--><br />
<br />
<br />
<br />
<!--[[File:smartrg_1.jpg|Configuring VDSL 1/5]]--><br />
<!--[[File:smartrg_2.jpg|Configuring VDSL 2/5]]--><br />
<!--[[File:smartrg_3.jpg|Configuring VDSL 3/5]]--><br />
<!--[[File:smartrg_4.jpg|Configuring VDSL 4/5]]--><br />
<!--[File:smartrg_5.jpg|Configuring VDSL 5/5]]--><br />
<br />
==== Add Settings for ADSL Mode====<br />
Moving on now to add settings for ADSL mode.<br />
ADSL plans include the following NCF DSL Plans:<br />
* Freedom 6/300<br />
* Freedom 7/300<br />
* Freedom 15-1/300<br />
<br />
#Click on "Advanced"<br />
#Click on "Layer2 Interface"<br />
#Click on "ATM Interface"<br />
#Click on "Add"<br />
<!--[[File:smartrg_505n_adsl01.png|Configuring ADSL2+ 1/11]]--><br />
<!--[[File:smartrg_505n_adsl02.png|Configuring ADSL2+ 2/11]]--><br />
[[File:smartrg_505n_adsl03.png|Configuring ADSL2+ 3/11]]<br />
#Under "Select DSL Latency", check both "Path0 (Fast)" and "Path1 (Interleaved)"<br />
#Ensure that VPI is 0 and that VCI is 35.<br />
# For everything else, use the defaults.<br />
#Scroll to the bottom of the page, and click "Next".<br />
[[File:smartrg_505n_adsl04.png|Configuring ADSL2+ 4/11]]<br />
# Click "Advanced"<br />
#Click "WAN Service"<br />
#Click "Add"<br />
[[File:smartrg_505n_adsl05.png|Configuring ADSL2+ 5/11]]<br />
#From the drop-down box, select "atm0/(4_0_35)"<br />
#Click "Next"<br />
[[File:smartrg_505n_adsl06.png|Configuring ADSL2+ 6/11]]<br />
#Ensure "PPPoE" is the active choice.<br />
#Ensure "Service description" is as shown.<br />
[[File:smartrg_505n_adsl07.png|Configuring ADSL2+ 7/11]]<br />
Ensure "Enable Firewall" and "Enable NAT" are checked. Scroll to the bottom of the page and click "Next".<br />
[[File:smartrg_505n_adsl08.png|Configuring ADSL2+ 8/11]]<br />
Click on "ppp0.1" and then "Next"<br />
[[File:smartrg_505n_adsl09.png|Configuring ADSL2+ 9/11]]<br />
Click on "ppp0.1" and then "Next"<br />
[[File:smartrg_505n_adsl10.png|Configuring ADSL2+ 10/11]]<br />
Click on "Apply/Save"<br />
[[File:smartrg_505n_adsl11.png|Configuring ADSL2+ 11/11]]<br />
'''You're done adding ADSL settings. Now, skip ahead to "Wireless Configuration".'''<br />
<br />
=== Configure as bridge ===<br />
Do this only if you prefer to use your own external router rather than the one built into your SmartRG unit.<br />
<br />
# Connect power and turn on the modem with the black button on the back.<br />
# Connect an Ethernet LAN cable to one of the yellow rear ports<br />
# In the browser's address bar, enter the IP address for the modem interface page: 192.168.1.1<br />
# If the modem is fresh from the factory, use the default user name and password to gain access<br />
##'''user:''' admin <br />
##'''password:''' admin<br />
<br />
If the modem was previously configured for someone, the password would be the previous user's DSL-Password. If it is unknown then do a reset to factory default, using a paper-clip in the reset hole on the back. Hold for 6 to 9 seconds to reset. The user name and password will now be as above.<br />
<br />
<br />
# Click on Advanced Setup and WAN Service and click on Add<br />
# The defaults are fine; click on Next.<br />
# Click on Bridging and ensure the 802.1P and 802.1Q are set to 0 and 35, then click on Next.<br />
# Click on Apply/Save<br />
# Done!<br />
<br />
See screenshots below:<br />
<br />
<br />
[[File:smartrg_505n_bridge_1.png|Configuring for Bridge Mode 1/5]]<br />
[[File:smartrg_505n_bridge_2.png|Configuring for Bridge Mode 2/5]]<br />
[[File:smartrg_505n_bridge_3.png|Configuring for Bridge Mode 3/5]]<br />
[[File:smartrg_505n_bridge_4.png|Configuring for Bridge Mode 4/5]]<br />
[[File:smartrg_505n_bridge_5.png|Configuring for Bridge Mode 5/5]]<br />
<br />
=== Wireless Configuration ===<br />
Continuing now to set the '''Wireless''' configuration<br />
# Ensure '''Enable Wireless''' is checked<br />
# The '''SSID''' is set to NCF plus a random number, such as '''NCF_123456'''. It is recommended you not use your first or last name, or street address as this information is broadcast and other people in your area will be able to associate the signal with which home it is coming from.<br />
# Click on '''Apply/Save''' at the bottom.<br />
# Click on '''Security''' on the left.<br />
# Set the '''Network Authentication''' to Mixed WPA2/WPA-PSK<br />
# Uncheck '''Use base MAC address as WPA/WAPI passphrase<br />
# Set the '''WPA/WAPI passphrase''' to be your DSL-Password<br />
# Click '''Apply/save'''.<br />
<br />
<br />
[[File:smartrg_505n_adsl12.png|Configuring Wireless 1/2]]<br />
[[File:smartrg_505n_adsl13.png|Configuring Wireless 2/2]]<br />
<br />
=== Password protect the Admin Role === <br />
# Click on '''Management''' on the left. Below it other options appear.<br />
# Select '''Access Control''' <br />
# Select '''Passwords''' <br />
# Enter '''admin''' for the User Name<br />
# Enter '''admin''' for the Old Password<br />
# For the New Password use your DSL-Password or another strong password. <br />
# Enter it once and again below to confirm<br />
# Save the changes with '''Apply/Save'''<br />
<br />
A pop-up log-in screen appears, and asks for sign-in. Use the User-ID '''admin''' and the DSL-Password just set. Return to the same configure page you were just at.<br />
<br />
<br />
[[File:smartrg_505n_adsl14.png|Setting Admin Password]]<br />
<br />
== See also ==<br />
*[[Dynamic DNS]]<br />
*[[Modem Configuration (DSL)]] - for a complete list of instructions for all NCF modems<br />
*[[Port forwarding]]<br />
[[Category: DSL]]</div>Fx315https://help.ncf.ca/index.php?title=SmartRG_SR505N_Configuration&diff=1896SmartRG SR505N Configuration2014-11-03T17:37:06Z<p>Fx315: /* Username Setup */</p>
<hr />
<div>[[File:sr505N-front.jpg|thumb|right|300px|The SmartRG SR505N Modem Front]]<br />
[[File:sr505n_back.jpg|thumb|right|300px|The SmartRG SR505N Modem Back]]<br />
This is the procedure NCF uses to configure a SmartRG SR505N modem out of the box or after a factory reset. To learn more about configuring your particular modem, consult the [[Modem manuals (DSL)|manual]].<br />
<br />
=== Configure router for Dual Mode ADSL/VDSL operation===<br />
Your router can support both ADSL mode and VDSL mode. If necessary, you could switch between ADSL plans and VDSL plans without having to buy a new router or even reconfigure your existing one.<br />
<br />
<br />
====Settings for VDSL====<br />
We'll start with the mode used for VDSL connections. These include the following NCF DSL Plans:<br />
* Freedom 15-10/300<br />
* Freedom 25/300<br />
* Freedom 50/300<br />
<br />
<br />
==== Getting Started ====<br />
NOTE: If the modem is brand new, "admin/admin" will be correct. If it's not new, it's recommended to reset the modem to factory defaults by holding down the reset button with a paper clip for 6 to 9 seconds and then do step 1.<br />
<br />
1. Once you access the modem browser at 191.168.1.1 and login ( admin/admin), click the link high-lighted in red.<br />
<br />
<br />
[[file:smartrg_1.jpg|Getting started]]<br />
<br />
==== Advanced Setup ====<br />
2. Click on the "Advanced Setup" link on the LH side of the page.<br />
[[file:smartrg_2.jpg|Advanced Setup]]<br />
<br />
==== WAN Service ====<br />
3. Click on the "WAN Service" link under "Advanced Setup" and then click on the "Edit" link highlighted in red.<br />
[[file:smartrg_3.jpg|WAN Service]]<br />
<br />
==== Username Setup ====<br />
4. On the 'PPP Username and Password' page, fill the username and password details in the field highlighted in red.<br />
Scroll to the bottom of this page - check that "Firewall" and "NAT" are enabled. Click "Next".<br />
[[file:smartrg_4.jpg|PPPOE set up]]<br />
<br />
==== PPPoE config save ====<br />
<!--5. There will be two more pages to scroll through and them you can finally "Save" these changes. At this point, the Internet light on the SmartRG should turn from red and eventually to green.--><br />
<br />
Click on "ppp0.1" and then "Next"<br />
[[File:smartrg_505n_adsl09.png|Configuring ADSL2+ 9/11]]<br />
Click on "ppp0.1" and then "Next"<br />
[[File:smartrg_505n_adsl10.png|Configuring ADSL2+ 10/11]]<br />
Click on "Apply/Save".<br />
[[file:smartrg_5.jpg|PPoE config save]]<br />
<br />
<!--==== Wireless Setup ====--><br />
<!--6. Click on the "Wireless" link on the RH side of the page.--><br />
<!--Change the SSID to the NCF standard name.--><br />
<!--Click on the "Security" subtab , store the NCF DSL password for the wi-fi password.--><br />
<br />
<!--====Modem Password Setup ====<br />
7. Click on the "Management " link on the RH side of the page. Click on the "Access"?? subtab and then the "Passwords" sub.sub tab. Change the modem access password to NCF standard.<br />
<br />
<br />
I need some more images to complete this - all in due time.--><br />
<br />
<br />
<br />
<!--[[File:smartrg_1.jpg|Configuring VDSL 1/5]]--><br />
<!--[[File:smartrg_2.jpg|Configuring VDSL 2/5]]--><br />
<!--[[File:smartrg_3.jpg|Configuring VDSL 3/5]]--><br />
<!--[[File:smartrg_4.jpg|Configuring VDSL 4/5]]--><br />
<!--[File:smartrg_5.jpg|Configuring VDSL 5/5]]--><br />
<br />
==== Add Settings for ADSL Mode====<br />
Moving on now to add settings for ADSL mode.<br />
ADSL plans include the following NCF DSL Plans:<br />
* Freedom 6/300<br />
* Freedom 7/300<br />
* Freedom 15-1/300<br />
<br />
#Click on "Advanced"<br />
#Click on "Layer2 Interface"<br />
#Click on "ATM Interface"<br />
#Click on "Add"<br />
<!--[[File:smartrg_505n_adsl01.png|Configuring ADSL2+ 1/11]]--><br />
<!--[[File:smartrg_505n_adsl02.png|Configuring ADSL2+ 2/11]]--><br />
[[File:smartrg_505n_adsl03.png|Configuring ADSL2+ 3/11]]<br />
#Under "Select DSL Latency", check both "Path0 (Fast)" and "Path1 (Interleaved)"<br />
#Ensure that VPI is 0 and that VCI is 35.<br />
# For everything else, use the defaults.<br />
[[File:smartrg_505n_adsl04.png|Configuring ADSL2+ 4/11]]<br />
# Click "Advanced"<br />
#Click "WAN Service"<br />
#Click "Add"<br />
[[File:smartrg_505n_adsl05.png|Configuring ADSL2+ 5/11]]<br />
#From the drop-down box, select "atm0/(4_0_35)"<br />
#Click "Next"<br />
[[File:smartrg_505n_adsl06.png|Configuring ADSL2+ 6/11]]<br />
#Ensure "PPPoE" is the active choice.<br />
#Ensure "Service description" is as shown.<br />
[[File:smartrg_505n_adsl07.png|Configuring ADSL2+ 7/11]]<br />
Ensure "Enable Firewall" and "Enable NAT" are checked.<br />
[[File:smartrg_505n_adsl08.png|Configuring ADSL2+ 8/11]]<br />
Click on "ppp0.1" and then "Next"<br />
[[File:smartrg_505n_adsl09.png|Configuring ADSL2+ 9/11]]<br />
Click on "ppp0.1" and then "Next"<br />
[[File:smartrg_505n_adsl10.png|Configuring ADSL2+ 10/11]]<br />
Click on "Apply/Save"<br />
[[File:smartrg_505n_adsl11.png|Configuring ADSL2+ 11/11]]<br />
'''You're done adding ADSL settings. Now, skip ahead to "Wireless Configuration".'''<br />
<br />
=== Configure as bridge ===<br />
Do this only if you prefer to use your own external router rather than the one built into your SmartRG unit.<br />
<br />
# Connect power and turn on the modem with the black button on the back.<br />
# Connect an Ethernet LAN cable to one of the yellow rear ports<br />
# In the browser's address bar, enter the IP address for the modem interface page: 192.168.1.1<br />
# If the modem is fresh from the factory, use the default user name and password to gain access<br />
##'''user:''' admin <br />
##'''password:''' admin<br />
<br />
If the modem was previously configured for someone, the password would be the previous user's DSL-Password. If it is unknown then do a reset to factory default, using a paper-clip in the reset hole on the back. Hold for 6 to 9 seconds to reset. The user name and password will now be as above.<br />
<br />
<br />
# Click on Advanced Setup and WAN Service and click on Add<br />
# The defaults are fine; click on Next.<br />
# Click on Bridging and ensure the 802.1P and 802.1Q are set to 0 and 35, then click on Next.<br />
# Click on Apply/Save<br />
# Done!<br />
<br />
See screenshots below:<br />
<br />
<br />
[[File:smartrg_505n_bridge_1.png|Configuring for Bridge Mode 1/5]]<br />
[[File:smartrg_505n_bridge_2.png|Configuring for Bridge Mode 2/5]]<br />
[[File:smartrg_505n_bridge_3.png|Configuring for Bridge Mode 3/5]]<br />
[[File:smartrg_505n_bridge_4.png|Configuring for Bridge Mode 4/5]]<br />
[[File:smartrg_505n_bridge_5.png|Configuring for Bridge Mode 5/5]]<br />
<br />
=== Wireless Configuration ===<br />
Continuing now to set the '''Wireless''' configuration<br />
# Ensure '''Enable Wireless''' is checked<br />
# The '''SSID''' is set to NCF plus a random number, such as '''NCF_123456'''. It is recommended you not use your first or last name, or street address as this information is broadcast and other people in your area will be able to associate the signal with which home it is coming from.<br />
# Click on '''Apply/Save''' at the bottom.<br />
# Click on '''Security''' on the left.<br />
# Set the '''Network Authentication''' to Mixed WPA2/WPA-PSK<br />
# Uncheck '''Use base MAC address as WPA/WAPI passphrase<br />
# Set the '''WPA/WAPI passphrase''' to be your DSL-Password<br />
# Click '''Apply/save'''.<br />
<br />
<br />
[[File:smartrg_505n_adsl12.png|Configuring Wireless 1/2]]<br />
[[File:smartrg_505n_adsl13.png|Configuring Wireless 2/2]]<br />
<br />
=== Password protect the Admin Role === <br />
# Click on '''Management''' on the left. Below it other options appear.<br />
# Select '''Access Control''' <br />
# Select '''Passwords''' <br />
# Enter '''admin''' for the User Name<br />
# Enter '''admin''' for the Old Password<br />
# For the New Password use your DSL-Password or another strong password. <br />
# Enter it once and again below to confirm<br />
# Save the changes with '''Apply/Save'''<br />
<br />
A pop-up log-in screen appears, and asks for sign-in. Use the User-ID '''admin''' and the DSL-Password just set. Return to the same configure page you were just at.<br />
<br />
<br />
[[File:smartrg_505n_adsl14.png|Setting Admin Password]]<br />
<br />
== See also ==<br />
*[[Dynamic DNS]]<br />
*[[Modem Configuration (DSL)]] - for a complete list of instructions for all NCF modems<br />
*[[Port forwarding]]<br />
[[Category: DSL]]</div>Fx315