DG4244 Bridge Configuration - Revision history

Gc884 at 21:55, 18 August 2026

2026-08-18T21:55:51Z

← Older revision		Revision as of 21:55, 18 August 2026
Line 6:		Line 6:
	# Open a browser and go to <nowiki>http://192.168.0.1</nowiki>.		# Open a browser and go to <nowiki>http://192.168.0.1</nowiki>.
	# Log in with your admin credentials. If you haven't changed them, the default username is admin and the default password is the alphanumeric code printed on the label on the back/bottom of the modem.		# Log in with your admin credentials. If you haven't changed them, the default username is admin and the default password is the alphanumeric code printed on the label on the back/bottom of the modem.
	# In the left-hand menu, click Gateway, then select At a Glance.		# In the left-hand menu, click '''Gateway''<nowiki/>', then select '<nowiki/>''At a Glance''<nowiki/>'.
	# Locate the Bridge Mode control and click Enable.		# Locate the Bridge Mode control and click '''Enable''<nowiki/>'.
	# Confirm the action if prompted. The modem will show a progress bar, apply the change, and reboot automatically. This can take 2–3 minutes.		# Confirm the action if prompted. The modem will show a progress bar, apply the change, and reboot automatically. This can take 2–3 minutes.

	'''To revert''': Reboot the modem and repeat these steps and select Disable on the Bridge Mode control, or perform a factory reset by holding the reset button on the back for about 20 seconds. Note that a factory reset also erases any other custom settings applied before		'''To revert''': Reboot the modem and repeat these steps and select '<nowiki/>''Disable''' on the Bridge Mode control, or perform a factory reset by holding the reset button on the back for about 20 seconds. Note that a factory reset also erases any other custom settings applied before.

	[[File:Sercomm_Bridge.png]]		[[File:Sercomm_Bridge.png]]

Gc884 at 21:51, 18 August 2026

2026-08-18T21:51:13Z

← Older revision		Revision as of 21:51, 18 August 2026
Line 11:		Line 11:

	'''To revert''': Reboot the modem and repeat these steps and select Disable on the Bridge Mode control, or perform a factory reset by holding the reset button on the back for about 20 seconds. Note that a factory reset also erases any other custom settings applied before		'''To revert''': Reboot the modem and repeat these steps and select Disable on the Bridge Mode control, or perform a factory reset by holding the reset button on the back for about 20 seconds. Note that a factory reset also erases any other custom settings applied before

			[[File:Sercomm_Bridge.png]]

Gc884 at 21:45, 18 August 2026

2026-08-18T21:45:15Z

← Older revision		Revision as of 21:45, 18 August 2026
Line 1:		Line 1:
	'''Before you start''':		'''Before you start''':
	By default, the Sercomm DG4244 operates in '''routed mode'''. Bridge mode disables the modem's built-in router functions (DHCP, Wi-Fi, firewall, port forwarding), so you'll need a separate router connected to it to handle these functions.		By default, the Sercomm DG4244 operates in '''routed mode'''. Bridge mode disables the modem's built-in router functions (DHCP, Wi-Fi, firewall, port forwarding), so you'll need a separate router connected to it to handle these functions.

			Follow these steps to switch your modem to '''bridge mode''':

			# Open a browser and go to <nowiki>http://192.168.0.1</nowiki>.
			# Log in with your admin credentials. If you haven't changed them, the default username is admin and the default password is the alphanumeric code printed on the label on the back/bottom of the modem.
			# In the left-hand menu, click Gateway, then select At a Glance.
			# Locate the Bridge Mode control and click Enable.
			# Confirm the action if prompted. The modem will show a progress bar, apply the change, and reboot automatically. This can take 2–3 minutes.

			'''To revert''': Reboot the modem and repeat these steps and select Disable on the Bridge Mode control, or perform a factory reset by holding the reset button on the back for about 20 seconds. Note that a factory reset also erases any other custom settings applied before

Gc884 at 21:24, 18 August 2026

2026-08-18T21:24:29Z

← Older revision		Revision as of 21:24, 18 August 2026
Line 1:		Line 1:
	'''Before you start''': By default, the Sercomm DG4244 operates in '''routed mode'''. Bridge mode disables the modem's built-in router functions (DHCP, Wi-Fi, firewall, port forwarding), so you'll need a separate router connected to it to handle these functions.		'''Before you start''':
			By default, the Sercomm DG4244 operates in '''routed mode'''. Bridge mode disables the modem's built-in router functions (DHCP, Wi-Fi, firewall, port forwarding), so you'll need a separate router connected to it to handle these functions.

Gc884: Created page with "'''Before you start''': By default, the Sercomm DG4244 operates in '''routed mode'''. Bridge mode disables the modem's built-in router functions (DHCP, Wi-Fi, firewall, port f..."

2026-08-18T21:23:07Z

Created page with "'''Before you start''': By default, the Sercomm DG4244 operates in '''routed mode'''. Bridge mode disables the modem's built-in router functions (DHCP, Wi-Fi, firewall, port f..."

New page

'''Before you start''': By default, the Sercomm DG4244 operates in '''routed mode'''. Bridge mode disables the modem's built-in router functions (DHCP, Wi-Fi, firewall, port forwarding), so you'll need a separate router connected to it to handle these functions.