Gc884: Included option to enable IPv6

2025-12-11T22:32:52Z

Included option to enable IPv6

← Older revision		Revision as of 22:32, 11 December 2025
Line 61:		Line 61:
	** PPPoE password: your DSL password		** PPPoE password: your DSL password
	** Check the box to the left for '''Enable NAT and Firewall'''		** Check the box to the left for '''Enable NAT and Firewall'''
			**Check the box to the left for '''Enable IPv6''', also make sure paremeters IANA and IAPD are selected.
	* Click '''Next''', then on each following page click '''Next''' until it changes to '''Apply/Save'''. Then click '''Apply/Save'''		* Click '''Next''', then on each following page click '''Next''' until it changes to '''Apply/Save'''. Then click '''Apply/Save'''
	\|-		\|-
Line 78:		Line 79:
	** PPPoE password: your DSL password		** PPPoE password: your DSL password
	** Check the box to the left for '''Enable NAT and Firewall'''		** Check the box to the left for '''Enable NAT and Firewall'''
			**Check the box to the left for '''Enable IPv6''', also make sure paremeters IANA and IAPD are selected.
	* Click '''Next''', then on each following page click '''Next''' until it changes to '''Apply/Save'''. Then click '''Apply/Save'''		* Click '''Next''', then on each following page click '''Next''' until it changes to '''Apply/Save'''. Then click '''Apply/Save'''
	\|-		\|-

Gc884 at 21:42, 10 October 2025

2025-10-10T21:42:43Z

← Older revision		Revision as of 21:42, 10 October 2025
Line 54:		Line 54:
	\|		\|
	* Click Add, then select '''atm0/(4_0_35)''', then click Next		* Click Add, then select '''atm0/(4_0_35)''', then click Next
	* On the '''WAN Service Configuration''' page, click Next		* On the '''WAN Service Configuration''' page, select:
			**PPP over Ethernet (PPPoE)
			**Internet Protocol Selection: IPv4 &I Pv6(Dual Stack), then click Next
	* On the '''PPP Username and Password''' page:		* On the '''PPP Username and Password''' page:
	** PPPoE username: your DSL username (format: aa000@ncf.ca		** PPPoE username: your DSL username (format: aa000@ncf.ca
	** PPPoE password: your DSL password		** PPPoE password: your DSL password
	** Check the box to the left for '''Enable ~~IPv6 for this service~~'''		** Check the box to the left for '''Enable NAT and Firewall'''
	* Click '''Next''', then on each following page click '''Next''' until it changes to '''Apply/Save'''. Then click '''Apply/Save'''		* Click '''Next''', then on each following page click '''Next''' until it changes to '''Apply/Save'''. Then click '''Apply/Save'''
	\|-		\|-
Line 68:		Line 70:
	* Click Add, then select '''ptm0/(4_1_1)''', then click Next		* Click Add, then select '''ptm0/(4_1_1)''', then click Next
	* On the '''WAN Service Configuration''' page:		* On the '''WAN Service Configuration''' page:
	** Change the setting of 802.1P Priority from '''-1''' to '''1'''		** Select PPP over Ethernet (PPPoE)
			**Change the setting of 802.1P Priority from '''-1''' to '''1'''
	** Change the setting of 802.1Q VLAN from '''-1''' to '''35'''		** Change the setting of 802.1Q VLAN from '''-1''' to '''35'''
			**Internet Protocol Selection: IPv4 &I Pv6(Dual Stack), then click Next
	* On the '''PPP Username and Password''' page:		* On the '''PPP Username and Password''' page:
	** PPPoE username: your DSL username (format: aa000@ncf.ca)		** PPPoE username: your DSL username (format: aa000@ncf.ca)
	** PPPoE password: your DSL password		** PPPoE password: your DSL password
	** Check the box to the left for '''Enable ~~IPv6 for this service~~'''		** Check the box to the left for '''Enable NAT and Firewall'''
	* Click '''Next''', then on each following page click '''Next''' until it changes to '''Apply/Save'''. Then click '''Apply/Save'''		* Click '''Next''', then on each following page click '''Next''' until it changes to '''Apply/Save'''. Then click '''Apply/Save'''
	\|-		\|-
Line 93:		Line 97:
	'''→ 5 GHz Band'''		'''→ 5 GHz Band'''

	~~'''→''' '''Security'''~~
	\|		\|
	* Disable WPS		* Network Authentication: '''WPA2-PSK'''
			* Password: your DSL password
	* Network Authentication to '''WPA2-PSK'''		* Encryption: '''AES'''
	* ~~WPA Passphrase~~ : your DSL password		*Band Steering: disabled. Then click '''Apply/Save'''
	* ~~WPA~~ Encryption : '''AES'''
	\|-		\|-
	\|10		\|10
Line 111:		Line 113:
	\|'''Wireless'''		\|'''Wireless'''
	'''→ 2.4 GHz Band'''		'''→ 2.4 GHz Band'''

	~~'''→''' '''Security'''~~
	\|		\|
	* Disable '''WPS'''
	* Network Authentication to '''WPA2-PSK'''		* Network Authentication to '''WPA2-PSK'''
	* WPA Passphrase : your DSL password		* WPA Passphrase: your DSL password
	* WPA Encryption : '''AES'''		* WPA Encryption: '''AES'''
			*Band Steering: disabled. Then click '''Apply/Save'''
	\|-		\|-
	\|12		\|12
Line 127:		Line 127:
	\|		\|
	* Username: '''admin'''		* Username: '''admin'''
	*New Username: '''admin'''

	* Old Password: admin (or whatever you set it to)		* Old Password: admin (or whatever you set it to)
	* New Password: your DSL password		* New Password: your DSL password
			*Confirm Password: your DSL password. Then click '''Apply/Save'''
	\|-		\|-
	\|13		\|13
Line 137:		Line 137:
	'''→ TR-069 Client'''		'''→ TR-069 Client'''
	\|		\|
	* Disable '''Inform'''		* Disable '''Inform. Then click Apply/Save'''

	* ACS URL: https://acs.ncf.ca
	\|-		\|-
	\|14		\|14
	~~\|System Log~~
	~~\|'''Management'''~~
	~~'''→ System Log'''~~

	~~'''→ Configure System Log'''~~
	~~\|Configuration:~~

	* Log:'''Enable'''
	* Log Level: '''Debugging'''
	* Display Level: '''Error'''
	* Mode: '''Local'''
	\|-
	~~\|15~~
	\|Internet Time		\|Internet Time
	\|'''Management'''		\|'''Management'''
Line 161:		Line 146:

	* Automatically synchronize with Internet time servers: '''Enable'''		* Automatically synchronize with Internet time servers: '''Enable'''
	* First NTP time server: '''Other''', then in the textbox to the right, put '''time.nrc.ca'''		* First NTP time server: Selec '''Other''', then in the textbox to the right, put '''time.nrc.ca'''
	* Time Zone: '''(GMT - 5:00) Eastern Time'''		* Time Zone: '''(GMT - 5:00) Eastern Time.''' Then click '''Apply/Save'''
	\|-		\|-
	\|16		\|15
	\|Backup Settings		\|Backup Settings
	\|'''Management'''		\|'''Management'''
Line 172:		Line 157:
	\|Settings -Backup		\|Settings -Backup

	* Backup Settings		* Click on Backup Settings
	\|}		\|}

Gc884 at 21:10, 10 October 2025

2025-10-10T21:10:15Z

← Older revision		Revision as of 21:10, 10 October 2025
Line 16:		Line 16:
	\|Log into Modem		\|Log into Modem
	\|<nowiki>http://192.168.1.1</nowiki>		\|<nowiki>http://192.168.1.1</nowiki>
	\|~~User Name: '''admin'''~~		\|Password: '''admin or your DSL password'''
	Password: '''admin'''
	\|-		\|-
	\|2		\|2

Gc884 at 21:09, 10 October 2025

2025-10-10T21:09:05Z

Show changes

Gc884: Created page with "The ovislink"

2025-10-10T21:07:03Z

Created page with "The ovislink"

New page

The ovislink

Ovislink OV978WAX Routed Configuration - Revision history

Gc884: Included option to enable IPv6

Gc884 at 21:42, 10 October 2025

Gc884 at 21:10, 10 October 2025

Gc884 at 21:09, 10 October 2025

Gc884: Created page with "The ovislink"