Ovislink OV978WAX Routed Configuration Fibre - Revision history

Gc884: Included steps to enable IPv6

2025-12-11T22:37:09Z

Included steps to enable IPv6

← Older revision		Revision as of 22:37, 11 December 2025
Line 51:		Line 51:
	** PPPoE password: your Fibre password		** PPPoE password: your Fibre password
	** Check the box to the left for '''Enable NAT and Firewall'''		** Check the box to the left for '''Enable NAT and Firewall'''
			** Check the box to the left for '''Enable IPv6''', also make sure paremeters IANA and IAPD are selected.
	* Click '''Next''', then on each following page click '''Next''' until it changes to '''Apply/Save'''. Then click '''Apply/Save'''		* Click '''Next''', then on each following page click '''Next''' until it changes to '''Apply/Save'''. Then click '''Apply/Save'''
	\|-		\|-

Gc884 at 22:42, 5 November 2025

2025-11-05T22:42:38Z

← Older revision		Revision as of 22:42, 5 November 2025
Line 30:		Line 30:
	'''→ Layer2 Interface'''		'''→ Layer2 Interface'''

	'''→ ~~PTM~~ Interface'''		'''→ ETH Interface'''
	\|		\|
	* Remove ~~'''ptm0'''~~ from the table by clicking the checkbox on the right, then click the '''Remove''' button		* Remove everything from the table by clicking the checkbox on the right, then click the '''Remove''' button
	* Click '''Add'''		* Click '''Add'''
	* ~~DSL Latency: Both checkboxes for~~ '''~~FAST~~''' ~~and~~ '''~~INTERLEAVED~~''' ~~should be checked~~		*Click on the drop-down menu and choose '''eth5/SFP''' as the interface, then click on '''Apply/Save'''
	\|-		\|-
	\|4		\|4
Line 41:		Line 41:
	'''→ WAN Service'''		'''→ WAN Service'''
	\|		\|
	* Click Add, then select '''~~ptm0~~/~~(4_1_1)~~''', then click Next		* Click Add, then select '''eth5/SFP''', then click Next
	* On the '''WAN Service Configuration''' page:		* On the '''WAN Service Configuration''' page:
	** Select PPP over Ethernet (PPPoE)		** Select '''PPP''' over Ethernet (PPPoE)
	**Change the setting of 802.1P Priority from '''-1''' to '''1'''		**Change the setting of 802.1P Priority from '''-1''' to '''1'''
	** Change the setting of 802.1Q VLAN from '''-1''' to '''40'''		** Change the setting of 802.1Q VLAN from '''-1''' to '''40'''
	**Internet Protocol Selection: IPv4 &~~I Pv6~~(Dual Stack), then click Next		**Internet Protocol Selection: '''IPv4 & IPv6''' (Dual Stack), then click Next
	* On the '''PPP Username and Password''' page:		* On the '''PPP Username and Password''' page:
	** PPPoE username: your Fibre username (format: aa000@ncf.ca)		** PPPoE username: your Fibre username (format: aa000@ncf.ca)
Line 63:		Line 63:
	\|'''Wireless'''		\|'''Wireless'''
	'''→ 5 GHz Band'''		'''→ 5 GHz Band'''
	\|SSID (WiFi Name) to format '''NCF_XXXX,''' where XXXX is the last 4 digits of your modem's serial number		\|'''SSID''' (WiFi Name) to format '''NCF_XXXX,''' where XXXX is the last 4 digits of your modem's serial number
	\|-		\|-
	\|7		\|7

Gc884 at 17:28, 17 October 2025

2025-10-17T17:28:56Z

← Older revision		Revision as of 17:28, 17 October 2025
Line 3:		Line 3:
	'''NCF Support''' is available to make configuring your OvisLink modem easier and to help you avoid potential mistakes. Here are simpler configuration options for your OvisLink modem. All settings in your modem not mentioned in these instructions can be ignored.		'''NCF Support''' is available to make configuring your OvisLink modem easier and to help you avoid potential mistakes. Here are simpler configuration options for your OvisLink modem. All settings in your modem not mentioned in these instructions can be ignored.

	# You can request a custom configuration file for your NCF ~~DSL~~ connection from [Mailto:support@ncf.ca support@ncf.ca].		# You can request a custom configuration file for your NCF Fibre connection from [Mailto:support@ncf.ca support@ncf.ca].
	# Call [Tel:613-721-1773 613-721-1773] x0 to book a Modem Appointment.		# Call [Tel:613-721-1773 613-721-1773] x0 to book a Modem Appointment.

Line 16:		Line 16:
	\|Log into Modem		\|Log into Modem
	\|<nowiki>http://192.168.1.1</nowiki>		\|<nowiki>http://192.168.1.1</nowiki>
	\|Password: '''admin or your ~~DSL~~ password'''		\|Password: '''admin or your Fibre password'''
	\|-		\|-
	\|2		\|2
Line 26:		Line 26:
	\|-		\|-
	\|3		\|3
	\|Enable ~~ADSL~~		\|Enable Fibre
	~~\|'''Advanced Setup'''~~
	~~'''→ Layer2 Interface'''~~

	~~'''→ ATM Interface'''~~
	\|
	* Remove '''atm0''' from the table by clicking the checkbox on the right, then click the Remove button
	* Click '''Add'''
	* Edit VPI and VCI. VPI should be 0, VCI should be 35
	* DSL Latency: Both checkboxes for '''FAST''' and '''INTERLEAVED''' should be checked
	\|-
	\|4
	~~\|Enable VDSL~~
	\|'''Advanced Setup'''		\|'''Advanced Setup'''
	'''→ Layer2 Interface'''		'''→ Layer2 Interface'''
Line 48:		Line 36:
	* DSL Latency: Both checkboxes for '''FAST''' and '''INTERLEAVED''' should be checked		* DSL Latency: Both checkboxes for '''FAST''' and '''INTERLEAVED''' should be checked
	\|-		\|-
	\|6		\|4
	\|Configure '''Fibre'''		\|Configure '''Fibre'''
	\|'''Advanced Setup'''		\|'''Advanced Setup'''
	'''→ WAN Service'''		'''→ WAN Service'''
Line 60:		Line 48:
	**Internet Protocol Selection: IPv4 &I Pv6(Dual Stack), then click Next		**Internet Protocol Selection: IPv4 &I Pv6(Dual Stack), then click Next
	* On the '''PPP Username and Password''' page:		* On the '''PPP Username and Password''' page:
	** PPPoE username: your ~~DSL~~ username (format: aa000@ncf.ca)		** PPPoE username: your Fibre username (format: aa000@ncf.ca)
	** PPPoE password: your ~~DSL~~ password		** PPPoE password: your Fibre password
	** Check the box to the left for '''Enable NAT and Firewall'''		** Check the box to the left for '''Enable NAT and Firewall'''
	* Click '''Next''', then on each following page click '''Next''' until it changes to '''Apply/Save'''. Then click '''Apply/Save'''		* Click '''Next''', then on each following page click '''Next''' until it changes to '''Apply/Save'''. Then click '''Apply/Save'''
	\|-		\|-
	\|7		\|5
	\|UPnP		\|UPnP
	\|'''Advanced Setup'''		\|'''Advanced Setup'''
Line 71:		Line 59:
	\|Disable '''uPnP'''		\|Disable '''uPnP'''
	\|-		\|-
	\|8		\|6
	\|WiFi 5GHz Name		\|WiFi 5GHz Name
	\|'''Wireless'''		\|'''Wireless'''
Line 77:		Line 65:
	\|SSID (WiFi Name) to format '''NCF_XXXX,''' where XXXX is the last 4 digits of your modem's serial number		\|SSID (WiFi Name) to format '''NCF_XXXX,''' where XXXX is the last 4 digits of your modem's serial number
	\|-		\|-
	\|9		\|7
	\|WiFi 5 GHz Security		\|WiFi 5 GHz Security
	\|'''Wireless'''		\|'''Wireless'''
Line 84:		Line 72:
	\|		\|
	* Network Authentication: '''WPA2-PSK'''		* Network Authentication: '''WPA2-PSK'''
	* Password: your ~~DSL~~ password		* Password: your Fibre password
	* Encryption: '''AES'''		* Encryption: '''AES'''
	*Band Steering: disabled. Then click '''Apply/Save'''		*Band Steering: disabled. Then click '''Apply/Save'''
	\|-		\|-
	\|10		\|8
	\|WiFi 2.4 GHz Name		\|WiFi 2.4 GHz Name
	\|'''Wireless'''		\|'''Wireless'''
Line 94:		Line 82:
	\|SSID (WiFi Name) to format '''NCF_XXXX,''' where XXXX is the last 4 digits of your modem's serial number		\|SSID (WiFi Name) to format '''NCF_XXXX,''' where XXXX is the last 4 digits of your modem's serial number
	\|-		\|-
	\|11		\|9
	\|WiFi 2.4 GHz Security		\|WiFi 2.4 GHz Security
	\|'''Wireless'''		\|'''Wireless'''
Line 100:		Line 88:
	\|		\|
	* Network Authentication to '''WPA2-PSK'''		* Network Authentication to '''WPA2-PSK'''
	* WPA Passphrase: your ~~DSL~~ password		* WPA Passphrase: your Fibre password
	* WPA Encryption: '''AES'''		* WPA Encryption: '''AES'''
	*Band Steering: disabled. Then click '''Apply/Save'''		*Band Steering: disabled. Then click '''Apply/Save'''
	\|-		\|-
	\|12		\|10
	\|Admin Password		\|Admin Password
	\|'''Management'''		\|'''Management'''
Line 114:		Line 102:

	* Old Password: admin (or whatever you set it to)		* Old Password: admin (or whatever you set it to)
	* New Password: your ~~DSL~~ password		* New Password: your Fibre password
	*Confirm Password: your ~~DSL~~ password. Then click '''Apply/Save'''		*Confirm Password: your Fibre password. Then click '''Apply/Save'''
	\|-		\|-
	\|13		\|11
	\|Remote Access		\|Remote Access
	\|'''Management'''		\|'''Management'''
Line 124:		Line 112:
	* Disable '''Inform. Then click Apply/Save'''		* Disable '''Inform. Then click Apply/Save'''
	\|-		\|-
	\|14		\|12
	\|Internet Time		\|Internet Time
	\|'''Management'''		\|'''Management'''
Line 134:		Line 122:
	* Time Zone: '''(GMT - 5:00) Eastern Time.''' Then click '''Apply/Save'''		* Time Zone: '''(GMT - 5:00) Eastern Time.''' Then click '''Apply/Save'''
	\|-		\|-
	\|15		\|13
	\|Backup Settings		\|Backup Settings
	\|'''Management'''		\|'''Management'''
Line 148:		Line 136:
	'''NCF Support''' is available to make configuring your OvisLink modem easier and to help you avoid potential mistakes. Here are simpler configuration options for your OvisLink modem:		'''NCF Support''' is available to make configuring your OvisLink modem easier and to help you avoid potential mistakes. Here are simpler configuration options for your OvisLink modem:

	# You can request a custom configuration file for your NCF ~~DSL~~ connection from [Mailto:support@ncf.ca support@ncf.ca.] You may need an alternate means of accessing the internet to download the configuration file.		# You can request a custom configuration file for your NCF Fibre connection from [Mailto:support@ncf.ca support@ncf.ca.] You may need an alternate means of accessing the internet to download the configuration file.
	# Call [Tel:613-721-1773 613-721-1773] x0 to book a Modem Appointment.		# Call [Tel:613-721-1773 613-721-1773] x0 to book a Modem Appointment.

Gc884 at 16:58, 17 October 2025

2025-10-17T16:58:49Z

← Older revision		Revision as of 16:58, 17 October 2025
Line 47:		Line 47:
	* Click '''Add'''		* Click '''Add'''
	* DSL Latency: Both checkboxes for '''FAST''' and '''INTERLEAVED''' should be checked		* DSL Latency: Both checkboxes for '''FAST''' and '''INTERLEAVED''' should be checked
	\|-
	\|5
	~~\|Configure ADSL~~
	~~\|'''Advanced Setup'''~~
	~~'''→ WAN Service'''~~
	\|
	* Click Add, then select '''atm0/(4_0_35)''', then click Next
	* On the '''WAN Service Configuration''' page, select:
	**PPP over Ethernet (PPPoE)
	**Internet Protocol Selection: IPv4 &I Pv6(Dual Stack), then click Next
	* On the '''PPP Username and Password''' page:
	** PPPoE username: your DSL username (format: aa000@ncf.ca
	** PPPoE password: your DSL password
	** Check the box to the left for '''Enable NAT and Firewall'''
	* Click '''Next''', then on each following page click '''Next''' until it changes to '''Apply/Save'''. Then click '''Apply/Save'''
	\|-		\|-
	\|6		\|6
	\|Configure ~~VDSL~~		\|Configure '''Fibre'''
	\|'''Advanced Setup'''		\|'''Advanced Setup'''
	'''→ WAN Service'''		'''→ WAN Service'''
Line 72:		Line 57:
	** Select PPP over Ethernet (PPPoE)		** Select PPP over Ethernet (PPPoE)
	**Change the setting of 802.1P Priority from '''-1''' to '''1'''		**Change the setting of 802.1P Priority from '''-1''' to '''1'''
	** Change the setting of 802.1Q VLAN from '''-1''' to '''35'''		** Change the setting of 802.1Q VLAN from '''-1''' to '''40'''
	**Internet Protocol Selection: IPv4 &I Pv6(Dual Stack), then click Next		**Internet Protocol Selection: IPv4 &I Pv6(Dual Stack), then click Next
	* On the '''PPP Username and Password''' page:		* On the '''PPP Username and Password''' page:
Line 78:		Line 63:
	** PPPoE password: your DSL password		** PPPoE password: your DSL password
	** Check the box to the left for '''Enable NAT and Firewall'''		** Check the box to the left for '''Enable NAT and Firewall'''
	* Click '''Next''', then on each following page click '''Next''' until it changes to '''Apply/Save'''. Then click '''Apply/Save'''		* Click '''Next''', then on each following page click '''Next''' until it changes to '''Apply/Save'''. Then click '''Apply/Save'''
	\|-		\|-
	\|7		\|7

Gc884 at 16:55, 17 October 2025

2025-10-17T16:55:13Z

Show changes

Gc884: Created page with "The Ovislink"

2025-10-17T16:53:35Z

Created page with "The Ovislink"

New page

The Ovislink