Modem Manuals

The manual for your NCF-supplied DSL modem can be found at the links below.

For instructions on how to configure these modems, see Modem Configuration (DSL)

TP-Link Modems

9970, four-port ethernet + "N" wireless ADSL/VDSL

• sold from January 2016
• 9970 home page
• User Guide
• Quick Installation Guide
• Datasheet
• NCF modem installation instruction sheet
• 9970 Emulator
• General TP-Link FAQ

8816, single ethernet port ADSL

• Sold from December 2011
• 8816 home page
• User Guide
• Datasheet
• NCF modem installation instruction sheet
• 8816 Emulator
• 8816 Firmware
• General TP-Link FAQ

8961ND, four-port ethernet + "N" wireless ADSL

• sold from January 2016
• 8961 home page
• User Guide
• Quick Installation Guide
• Datasheet
• [NCF modem installation instruction sheet]
• 8961 Emulator
• 8961 Firmware
• General TP-Link FAQ

8951ND, four-port ethernet + "N" wireless ADSL

• sold from November 2012 to January 2016
• 8951G home page
• User Guide
• Quick Installation Guide
• Datasheet
• NCF modem installation instruction sheet
• 8951 Emulator
• 8951 Firmware
• General TP-Link FAQ

8950ND, four-port ethernet + "N" wireless ADSL

• sold from December 2011 until October 2012
• 8950G home page
• User Guide
• Quick Installation Guide
• Datasheet
• 8950 Firmware
• 8950 Emulator
• General TP-Link FAQ

8901G, four-port ethernet + "G" wireless ADSL

• sold from December 2011 until October 2012
• AVOID/REPLACE (known security hole)
• Security Breach
• 8901G home page
• User Guide
• Quick Installation Guide
• Datasheet
• 8901-G Emulator
• 8901-G Firmware
• General TP-Link FAQ

8616, one-port modem only, NO PPPoe log-in capability

Very rarely encountered. Strictly a modem, does not have the capability to dynamically assign an IP address to any hosts. User must assign one manually. The modem manual details the process well in Section 3.1. NOTE: This does not supply the user with a Static IP address.

Note that configuring this device on a computer with more than one Ethernet interface requires that you temporarily disable one of them, due to the 8616's lack of DHCP services. So, issue a terminal command of "ifconfig eth0 down" before configuring the modem. The modem only requires a VPI and VCI. It is not necessary to specify PVC2.

• Modem Manual
• PPPoe Configuration (third party)
• 8816 Firmware
• General TP-Link FAQ

SmartRG Modem

SR505N, four-port ethernet + "N" wireless VDSL

• sold from September 2014 to January 2016
• Home Page
• Data Sheet
• Modem Manual
• NCF modem instruction sheet
• Modem Configuration (DSL) SmartRG SR505N
• SR505N Emulator
• SR505N Firmware (third party)
• Bridge Mode Instructions (third party)

Sagemcom Modem

2864, four-port ethernet + "N" wireless VDSL

• sold from November 2013 to August 2014
• There do not seem to be any manuals available from the manufacturer for this modem
• Modem Configuration (DSL) Sagemcom 2864
• Sagemcom 2864 set-up PDF

Thomson Gateways

NCF sold Thomson modems prior to December 2011. Before 2010, Thomson Gateway (TG) DSL modems ('gateways') were called 'SpeedTouch' (ST).

TG585 DSL modem version 8, four-port ethernet + wireless "G" ADSL

• sold from summer of 2011 until December 2011
• Setup and User Guide
• Guide d'installation et de l'utilisateur
• Datasheet
• ST585 v8 Emulator
• TG585 v8 Firmware
• TG585 FAQ

TG585 DSL modem version 7, four-port ethernet + wireless "G" ADSL

• sold from late 2009 until spring 2011
• Setup and User Guide
• Guide d'installation et de l'utilisateur
• Datasheet
• TG585 v7 Firmware

ST585 DSL modem version 6, four-port ethernet + wireless "G" ADSL

• sold until approx late 2009
• Setup and User Guide
• Guide d'installation et de l'utilisateur
• ST585 Firmware

ST516 modem version 6, single ethernet port ADSL

• sold until December 2011
• Setup and User Guide
• Guide d'installation et de l'utilisateur
• Datasheet
• ST516 Emulator
• ST516 Firmware

Bell Modems (not sold by NCF)

Bell 2wire 2701HG-G, four ethernet ports, wireless "G", ADSL

• Setup and User Guide
• Home-Networking Guide
• Bell Tutorials

See also

• Dynamic DNS
• Firmware
• Modem Configuration (DSL)
• Port forwarding
• SpeedTouch 516 and 585 on ADSL2+