Head blueLogoText.gif NCF HelpWiki
Help | StartPage

Difference between revisions of "Ovislink OV978WAX Routed Configuration Fibre"

From Support
Jump to navigation Jump to search
Line 47: Line 47:
* Click '''Add'''
* Click '''Add'''
* DSL Latency: Both checkboxes for '''FAST''' and '''INTERLEAVED'''  should be checked
* DSL Latency: Both checkboxes for '''FAST''' and '''INTERLEAVED'''  should be checked
|-
|5
|Configure ADSL
|'''Advanced Setup'''
'''→ WAN Service'''
|
* Click Add, then select '''atm0/(4_0_35)''', then click Next
* On the  '''WAN Service Configuration''' page, select:
**PPP over Ethernet (PPPoE)
**Internet Protocol Selection: IPv4 &I Pv6(Dual Stack), then click Next
* On the '''PPP Username and Password''' page:
** PPPoE username: your DSL username (format: aa000@ncf.ca
** PPPoE password: your DSL password
** Check the box to the left for '''Enable NAT and Firewall'''
* Click '''Next''', then on each following page click '''Next''' until it  changes to '''Apply/Save'''. Then click '''Apply/Save'''
|-
|-
|6
|6
|Configure VDSL
|Configure '''Fibre'''
|'''Advanced Setup'''
|'''Advanced Setup'''
'''→ WAN Service'''
'''→ WAN Service'''
Line 72: Line 57:
** Select PPP over Ethernet (PPPoE)
** Select PPP over Ethernet (PPPoE)
**Change the setting of 802.1P Priority from '''-1''' to '''1'''
**Change the setting of 802.1P Priority from '''-1''' to '''1'''
** Change the setting of 802.1Q VLAN from '''-1''' to '''35'''
** Change the setting of 802.1Q VLAN from '''-1''' to '''40'''
**Internet Protocol Selection: IPv4 &I Pv6(Dual Stack), then click Next
**Internet Protocol Selection: IPv4 &I Pv6(Dual Stack), then click Next
* On the '''PPP Username and Password''' page:
* On the '''PPP Username and Password''' page:
Line 78: Line 63:
** PPPoE password: your DSL password
** PPPoE password: your DSL password
** Check the box to the left for '''Enable NAT and Firewall'''
** Check the box to the left for '''Enable NAT and Firewall'''
* Click '''Next''', then on each following page click '''Next''' until it  changes to '''Apply/Save'''. Then click '''Apply/Save'''  
* Click '''Next''', then on each following page click '''Next''' until it  changes to '''Apply/Save'''. Then click '''Apply/Save'''
|-
|-
|7
|7

Revision as of 11:58, 17 October 2025

Ovislink OV978WAX
 Ovislink Front Ovislink Back Ovislink Side

with WiFi

NCF Support is available to make configuring your OvisLink modem easier and to help you avoid potential mistakes. Here are simpler configuration options for your OvisLink modem. All settings in your modem not mentioned in these instructions can be ignored.

  1. You can request a custom configuration file for your NCF DSL connection from support@ncf.ca.
  2. Call 613-721-1773 x0 to book a Modem Appointment.
Steps to Configure OvisLink for Routed Operation
Steps Menu Navigation Parameters
1 Log into Modem http://192.168.1.1 Password: admin or your DSL password
2 WAN Cleanup Advanced Setup

→ WAN Service

Remove everything from the WAN Service Table by clicking the checkbox on the right for each entry,

then click the Remove button

3 Enable ADSL Advanced Setup

→ Layer2 Interface

→ ATM Interface

  • Remove atm0 from the table by clicking the checkbox on the right, then click the Remove button
  • Click Add
  • Edit VPI and VCI. VPI should be 0, VCI should be 35
  • DSL Latency: Both checkboxes for FAST and INTERLEAVED should be checked
4 Enable VDSL Advanced Setup

→ Layer2 Interface

→ PTM Interface

  • Remove ptm0 from the table by clicking the checkbox on the right, then click the Remove button
  • Click Add
  • DSL Latency: Both checkboxes for FAST and INTERLEAVED should be checked
6 Configure Fibre Advanced Setup

→ WAN Service

  • Click Add, then select ptm0/(4_1_1), then click Next
  • On the WAN Service Configuration page:
    • Select PPP over Ethernet (PPPoE)
    • Change the setting of 802.1P Priority from -1 to 1
    • Change the setting of 802.1Q VLAN from -1 to 40
    • Internet Protocol Selection: IPv4 &I Pv6(Dual Stack), then click Next
  • On the PPP Username and Password page:
    • PPPoE username: your DSL username (format: aa000@ncf.ca)
    • PPPoE password: your DSL password
    • Check the box to the left for Enable NAT and Firewall
  • Click Next, then on each following page click Next until it changes to Apply/Save. Then click Apply/Save
7 UPnP Advanced Setup

→ UPnP

Disable uPnP
8 WiFi 5GHz Name Wireless

→ 5 GHz Band

SSID (WiFi Name) to format NCF_XXXX, where XXXX is the last 4 digits of your modem's serial number
9 WiFi 5 GHz Security Wireless

→ 5 GHz Band

  • Network Authentication: WPA2-PSK
  • Password: your DSL password
  • Encryption: AES
  • Band Steering: disabled. Then click Apply/Save
10 WiFi 2.4 GHz Name Wireless

→ 2.4 GHz Band

SSID (WiFi Name) to format NCF_XXXX, where XXXX is the last 4 digits of your modem's serial number
11 WiFi 2.4 GHz Security Wireless

→ 2.4 GHz Band

  • Network Authentication to WPA2-PSK
  • WPA Passphrase: your DSL password
  • WPA Encryption: AES
  • Band Steering: disabled. Then click Apply/Save
12 Admin Password Management

→ Access Controls

→ Passwords

  • Username: admin
  • Old Password: admin (or whatever you set it to)
  • New Password: your DSL password
  • Confirm Password: your DSL password. Then click Apply/Save
13 Remote Access Management

→ TR-069 Client

  • Disable Inform. Then click Apply/Save
14 Internet Time Management

→ Internet Time

Time settings:
  • Automatically synchronize with Internet time servers: Enable
  • First NTP time server: Selec Other, then in the textbox to the right, put time.nrc.ca
  • Time Zone: (GMT - 5:00) Eastern Time. Then click Apply/Save
15 Backup Settings Management

→ Settings

→ Backup

Settings -Backup
  • Click on Backup Settings

with separate WiFi Router

NCF Support is available to make configuring your OvisLink modem easier and to help you avoid potential mistakes. Here are simpler configuration options for your OvisLink modem:

  1. You can request a custom configuration file for your NCF DSL connection from support@ncf.ca. You may need an alternate means of accessing the internet to download the configuration file.
  2. Call 613-721-1773 x0 to book a Modem Appointment.

Configure your modem for Routed Operation

If you have a router, we recommend the following configuration steps:  

  1. Follow the configuration steps outline for Routed Operation with WiFi and make the following changes:
    • Under Wireless, Uncheck the Enable Wireless Option
    • Click Apply/Save

Router configuration

2. On your router, set the Connection Mode or Type to Automatic IP, Automatic DHCP or Dynamic IP mode

See Also

Back to the Top

Retrieved from "https://help.ncf.ca/index.php?title=Ovislink_OV978WAX_Routed_Configuration_Fibre&oldid=8503"