Head blueLogoText.gif NCF HelpWiki
Help | StartPage

Difference between revisions of "TP-Link TD-W9970 Configuration"

From Support
Jump to navigation Jump to search
m
m
 
(54 intermediate revisions by 3 users not shown)
Line 1: Line 1:
<div class="ncfrightbox"> {{Template:Modem Links}} </div>
<div class="ncfrightbox w-25">{{Template:TP-Link TD-W9970}}</div>
 
[[File:TD-W9970_front.jpg|thumb|left|x250px|The TP-Link TD-W9970 Modem Front]]
[[File:TD-W9970_front.jpg|thumb|left|x250px|The TP-Link TD-W9970 Modem Front]]
[[File:TD-W9970_back.jpg|thumb|left|x250px|The TP-Link TD-W9970 Modem Back]]
[[File:TD-W9970_back.jpg|thumb|left|x250px|The TP-Link TD-W9970 Modem Back]]
The TP-Link TD-W9970 is for use on any service on networks using Bells' DSL infrastructure.
The TP-Link TD-W9970 is for use on any service on networks using Bell's DSL infrastructure. To learn more about configuring your particular modem, consult the [[Modem Manuals#TP-Link Modems|manual]].
 
=Routed=


This is the procedure NCF uses to configure a TP-Link TD-W9970 modem out of the box or after a factory reset. To learn more about configuring your particular modem, consult the [[Modem Manuals#TP-Link Modems|manual]].
The TP-Link TD-W9970 modem router supports both ADSL and VDSL, and switches automatically to match the line it is connected to.  


= Configure router for Dual-Mode ADSL/VDSL operation=
==VDSL==
Your router can support both ADSL and VDSL modes. If necessary, you could switch between ADSL and VDSL plans without having to buy a new router or even reconfigure your existing one.
{{Template:TD-W9970_Links}}


==Settings for VDSL==
We will start with the mode used for VDSL connections.  
We will start with the mode used for VDSL connections. These include the following NCF DSL Plans:
* Freedom 10-7/Unl
* Freedom 15-10/Unl
* Freedom 25/Unl
* Freedom 50/Unl


== Quick Setup ==
If the modem is new, a user name of '''admin''' and password of '''admin''' will gain access to the modem configuration. If the modem is not new, it is recommended to reset the modem to the factory default settings by holding down the '''Reset/Wi-Fi''' button for 6 to 9 seconds before continuing to Quick Setup Step 1 below.
'''NOTE:''' If the modem is brand new, "user name: admin" and "password: admin" will gain access.


If the modem is not new, it is recommended to reset the modem to the factory defaults by holding down the '''Reset/Wi-Fi''' button for 6 to 9 seconds and then do step 1.
'''Quick Setup'''


1. Once you access the modem from your [[browser]] at http://192.168.1.1 and login (user name: admin and password: admin), click the '''Quick Setup''' link in the Menu on the left.  
1. Once you access the modem from your [[browser]] at http://192.168.1.1 and login (user name: admin and password: admin), click the '''Quick Setup''' link in the Menu on the left.


Then click '''Next''' on the '''Quick Setup-Start''' page.
Then click '''Next''' on the '''Quick Setup-Start''' page.


[[file:Td-w9970_setup1.png|1050x1050px|Getting started]]
[[file:Td-w9970_setup1.png|721x721px|Getting started]]
 
'''Region and Time Zone'''
 
{{Template:Back to the Top}}


=== '''Region and Time Zone''' ===
# Set Region to '''Canada'''
# Set Region to '''Canada'''
# Time Zone to '''(GMT-05:00) Eastern Time (US & Canada)'''
# Time Zone to '''(GMT-05:00) Eastern Time (US & Canada)'''
# Click '''Next'''
# Click '''Next'''


[[file:Td-w9970_setup2.png|1121x1121px|Step2]]
[[file:Td-w9970_setup2.png|722x722px|Step2]]
 
'''Auto Detection'''
 
{{Template:Back to the Top}}


=== '''Auto Detection''' ===
# Click on '''No, I want to configure The Internet Connection myself'''
# Click on '''No, I want to configure The Internet Connection myself'''
# Click '''Next'''
# Click '''Next'''


[[file:Td-w9970_setup3.png|1012x1012px|Step3]]
[[file:Td-w9970_setup3.png|724x724px|Step3]]
 
'''DSL'''
 
{{Template:Back to the Top}}


'''Quick Setup – DSL'''
# ISP: '''Other'''
# ISP: '''Other'''
# L2 Interface Type: '''VDSL'''
# L2 Interface Type: '''VDSL'''
Line 48: Line 54:
# Click '''Next'''
# Click '''Next'''


[[file:Td-w9970_setup4.png|1009x1009px|Step4]]
[[file:Td-w9970_setup4.png|721x721px|Step4]]
 
'''PPPoE'''
 
{{Template:Back to the Top}}


'''Quick Setup - PPPoE'''
# User name: '''ab123@ncf.ca''' (where ab123 is your NCF ID)
# User name: '''ab123@ncf.ca''' (where ab123 is your NCF ID)
# Password: '''••••••••''' (where •••••••• is your NCF DSL Password)
# Password: '''••••••••''' (where •••••••• is your NCF DSL Password)
Line 56: Line 65:
# Click '''Next'''
# Click '''Next'''


[[file:Td-w9970_setup5.png|974x974px|Step5]]
[[file:Td-w9970_setup5.png|725x725px|Step5]]
 
'''3G/4G'''
 
{{Template:Back to the Top}}


'''Quick Setup – 3G/4G'''
# Click '''Next'''
# Click '''Next'''


[[file:Td-w9970_setup6.png|970x970px|Step6]]
[[file:Td-w9970_setup6.png|729x729px|Step6]]
 
'''Wireless'''
 
{{Template:Back to the Top}}
 
'''IMPORTANT NOTE:''' The Quick Setup process will not set the Wireless Security to use WPA2 exclusively with AES-- this means more recent devices connecting to the device may warn of insufficient security when connecting over Wi-Fi. To avoid this, after completing the Quick Setup, access the Wireless settings for the device, and ensure only '''WPA2''' is selected for the Security protocol, and '''AES''' for the encryption method. A selection of WPA/WPA2 and AES/TKIP is less secure and will cause newer device to issue warnings.


'''Quick Setup – Wireless'''
# Wireless: '''Enable'''
# Wireless: '''Enable'''
# Wireless Network Name (SSID): '''NCF_XXXX''' (where XXXX are the last 4 digits of the modem serial number)
# Wireless Network Name (SSID): '''NCF_XXXX''' (where XXXX are the last 4 digits of the modem serial number)
Line 72: Line 89:
# Click '''Next'''
# Click '''Next'''


[[file:Td-w9970_setup7.png|947x947px|Step7]]
[[file:Td-w9970_setup7.png|705x705px|Step7]]
 
'''Confirm'''
 
{{Template:Back to the Top}}


'''Quick Setup – Confirm'''
# Verify all setting are as entered
# Verify all setting are as entered
# Click '''Next'''
# Click '''Next'''


[[file:Td-w9970_setup8.png|961x961px|Step8]]
[[file:Td-w9970_setup8.png|711x711px|Step8]]


'''Quick Setup – Complete'''
'''Complete'''
# Click Finish
 
{{Template:Back to the Top}}
 
# Click '''Finish'''


'''Stay logged-in'''
'''Stay logged-in'''
Line 87: Line 110:
#Click '''WAN Settings'''
#Click '''WAN Settings'''


'''Network – WAN Settings'''
'''DSL WAN Interface'''
# Click on '''Action: Edit''' (entry with pppoe_ptm_xx_x_x, right-hand side of table)
# Click on '''Action: Edit''' (entry with pppoe_ptm_35_1_d, right-hand side of table)
 
'''WAN Settings'''
 
{{Template:Back to the Top}}


'''Network – WAN Settings'''
# WAN Service Setup, enter...
# WAN Service Setup, enter...
# Enable IPv6: '''Select off'''
# Enable IPv6: '''Selected'''
# Click '''Advance'''
# Click '''Advance'''
# Enable SPI Firewall: '''selected'''
# Enable SPI Firewall: '''selected'''
# Enable IGMP Proxy: '''un-select'''
# Enable IGMP Proxy: '''un-select'''
# Click '''Save'''
# Click '''Save'''
'''Wireless Settings'''{{Template:Back to the Top}}
# Click '''Wireless''' (in left-hand menu)
# Click '''Wireless Security'''
# Ensure WPA/WPA2 (Personal) is selected
# Authentication Type: '''WPA2-PSK'''
# Encryption: '''AES'''
# Click '''Save'''
== ADSL ==
{{Template:TD-W9970_Links}}


== Add Settings for ADSL ==
Moving on now to add settings for ADSL.
Moving on now to add settings for ADSL.
ADSL is required for the following NCF DSL Plans:
* Freedom 6/300
* Freedom 7/300
* Freedom 15-1/300


'''Stay logged-in'''
'''Stay logged-in'''
Line 109: Line 141:
# Click '''WAN Settings'''
# Click '''WAN Settings'''


'''Network – WAN Settings – DSL WAN Interface'''
'''DSL WAN Interface'''
 
{{Template:Back to the Top}}
 
# Click on '''Action: Delete''' (1st entry, right-hand side of table)
# Click on '''Action: Delete''' (1st entry, right-hand side of table)
# Click '''Add''' button
# Then click '''Add''' button


[[file:Td-w9970_setup9.png|997x997px|Adding ADSL2+ WAN Config 1/2]]
[[file:Td-w9970_setup9.png|1195x1195px|Adding ADSL2+ WAN Config 1/2]]
 
'''WAN Settings'''
 
{{Template:Back to the Top}}


'''WAN Service Setup, enter...'''
# DSL Modulation Type: '''ADSL'''
# DSL Modulation Type: '''ADSL'''
# ATM Configuration: '''VPI/VCI = 0/35'''
# ATM Configuration: '''VPI/VCI = 0/35'''
# Connection Type: '''PPPoE'''
# WAN Service Setup
# User name: '''ab123@ncf.ca''' (where ab123 is your NCF ID)
## Connection Type: '''PPPoE'''
# Password: '''••••••••''' (where •••••••• is your NCF DSL Password)
## PPP Username: '''ab123@ncf.ca''' (where ab123 is your NCF ID)
# Confirm password: '''••••••••'''
## PPP Password: '''••••••••''' (your NCF DSL Password)
# Connection Mode: select '''Always on'''
## Confirm password: '''••••••••'''
# Authentication Type: select '''AUTO_AUTH'''
## Enable IPv4: '''selected'''
# Enable IPv4: '''selected'''
## Enable IPv6: '''select'''
# Default Gateway: select '''Current Connection'''
# Enable IPv6: '''select'''
# Click '''Advance'''
# Click '''Advance'''
# Enable SPI Firewall: '''selected'''
## Enable SPI Firewall: '''selected'''
# Enable IGMP Proxy: '''un-select'''
## Enable IGMP Proxy: '''un-select'''
# Click '''Save'''
# Click '''Save'''


[[file:Td-w9970_setup10.png|860x860px|Adding ADSL2+ WAN Config 2/2]]
[[file:Td-w9970_setup10.png|804x804px|Adding ADSL2+ WAN Config 2/2]]
 
== DNS Fix ==
{{Template:TD-W9970_Links}}


== Fix Unresponsive DNS Issue ==
There is a known issue where the internal DNS server sometimes stop responding after swapping between ADSL and VDSL connections. To avoid this issue, we recommend hard-coding a public DNS server instead of using the internal one.
There is a known issue where the internal DNS server sometimes stop responding after swapping between ADSL and VDSL connections. To avoid this issue, we recommend hard-coding a public DNS server instead of using the internal one.


Line 141: Line 179:
# Secondary DNS Server: '''1.0.0.1'''
# Secondary DNS Server: '''1.0.0.1'''


[[file:02-dsn-fix.png|800px|DNS Fix for TD-W9970]]
[[file:02-dsn-fix.png|720x720px|DNS Fix for TD-W9970]]


== Additional Settings ==
== UPnP ==
{{Template:TD-W9970_Links}}


'''UPnP'''
# Click on '''Forwarding''' (left-hand menu, near the middle)
# Click on '''Forwarding''' (left-hand menu, near the middle)
# UPnP: '''de-select'''
# UPnP: '''de-select'''
[[File:TD-W9970_setup13.png|frameless|732x732px]]
== Time ==
{{Template:TD-W9970_Links}}


'''Time Settings'''
# Click on '''System Tools''' (left-hand menu, towards the bottom)
# Click on '''System Tools''' (left-hand menu, towards the bottom)
# Select '''Time Settings'''
# Select '''Time Settings'''
Line 159: Line 200:
# Click '''Save'''
# Click '''Save'''


'''Manage Control'''
[[file:Td-w9970_setup12.png|734x734px|Configuring Time Settings]]
 
== Manage Control==
{{Template:TD-W9970_Links}}
 
# Click on '''System Tools''' (left-hand menu, towards the bottom)
# Click on '''System Tools''' (left-hand menu, towards the bottom)
# Select '''Manage Control'''
# Select '''Manage Control'''
Line 165: Line 210:
# Enter it once and again below to confirm
# Enter it once and again below to confirm
# Ensure ICMP (Ping) is set to '''Local only''' (default setting)
# Ensure ICMP (Ping) is set to '''Local only''' (default setting)
# Click '''Save'''
#Click '''Save'''  
 
[[File:Td-w9970_setup11.png|frameless|713x713px]]
 
== CWMP ==
{{Template:TD-W9970_Links}}


'''CWMP Settings'''
# Click on '''System Tools''' (left-hand menu, towards the bottom)
# Click on '''System Tools''' (left-hand menu, towards the bottom)
# Select '''CWMP Settings'''
# Select '''CWMP Settings'''
Line 174: Line 223:
# Click '''Save'''
# Click '''Save'''


== Modem Password Setup ==
==Firewall==
Click on the "System Tools" link on the LH side of the page, then "Manage Control".  Change the modem access password to NCF standard.
{{Template:TD-W9970_Links}}
 
[[file:Td-w9970_setup11.png|800px|Setting Admin Password]]
 
== Configuring Time Zone ==
Click on the "System Tools" link on the LH side of the page, then "Time Settings".  Set the timezone to Eastern Standard Time, enable DST (Daylight Savings Time), and set the NTP server to the NRC clocks (time.nrc.ca).


[[file:Td-w9970_setup12.png|800px|Configuring Time Settings]]
# Click '''Firewall''' in the left column
# Select '''Enable Firewall''' if it's not '''Enabled'''


==Turn on the Firewall==
=Bridge=
*Click 'Firewall' in the left column
{{Template:TD-W9970_Links}}
*Select 'Enable Firewall'


=Configure as bridge=
Do this only if you prefer to use your own external router rather than the one built into your TP-Link unit.
Do this only if you prefer to use your own external router rather than the one built into your TP-Link unit.


# Connect power and turn on the modem with the button on the back.
# Connect power and turn on the modem with the button on the back.
# Connect an Ethernet LAN cable to one of the yellow rear ports
# Connect an Ethernet LAN cable to one of the yellow rear ports
# In the browser's address bar, enter the IP address for the modem interface page: 192.168.1.1
# In the browser's address bar, enter the IP address for the modem interface page: [http://192.168.1.1 192.168.1.1]
# If the modem is fresh from the factory, use the default user name and password to gain access
# If the modem is fresh from the factory, use the default user name and password to gain access
##'''user:''' admin  
##'''user:''' admin  
Line 200: Line 243:
If the modem was previously configured for someone, the password would be the previous user's [[DSL password]]. If it is unknown then do a reset to factory default, press the reset/Wi-Fi button on the back. Hold for 6 to 9 seconds to reset. The user name and password will now be as above.
If the modem was previously configured for someone, the password would be the previous user's [[DSL password]]. If it is unknown then do a reset to factory default, press the reset/Wi-Fi button on the back. Hold for 6 to 9 seconds to reset. The user name and password will now be as above.


# Click on Quick Setup.
==VDSL==
{{Template:TD-W9970_Links}}


See screenshots below:
# Click on '''Quick Setup'''.
 
'''DSL'''
{{Template:Back to the Top}}


'''Quick Setup – DSL'''
# ISP: '''Other'''
# ISP: '''Other'''
# L2 Interface Type: '''VDSL'''
# L2 Interface Type: '''VDSL'''
Line 212: Line 258:
# Click '''Next'''
# Click '''Next'''


[[File:Td-w9970_bridge1.png|800px|Configuring for Bridge Mode 1/4]]
[[File:Td-w9970_bridge1.png|692x692px|Configuring for Bridge Mode 1/4]]
 
'''Wireless'''
{{Template:Back to the Top}}


'''Quick Setup – Wireless'''
# Wireless: '''Disable'''
# Wireless: '''Disable'''
# Click '''Next'''
# Click '''Next'''


[[File:Td-w9970_bridge4.png|800px|Configuring for Bridge Mode 4/4]]
[[File:Td-w9970_bridge4.png|689x689px|Configuring for Bridge Mode 4/4]]
 
'''Confirm'''
{{Template:Back to the Top}}


'''Quick Setup – Confirm'''
# Verify all setting are as entered
# Verify all setting are as entered
# Click '''Next'''
# Click '''Next'''


[[File:Td-w9970_bridge2.png|800px|Configuring for Bridge Mode 2/4]]
[[File:Td-w9970_bridge2.png|687x687px|Configuring for Bridge Mode 2/4]]


'''Stay logged-in'''
'''Stay logged-in'''
# Click '''Network''' (left-hand menu, 4th link from top)
# Click '''Network''' (left-hand menu, 4th link from top)
# Click '''WAN Settings'''
# Click '''WAN Settings'''
# On the '''DSL WAN Interface''' page click '''Add'''


'''Network – WAN Settings – WAN Settings'''
==ADSL==
{{Template:TD-W9970_Links}}
 
'''WAN Settings'''
# DSL Modulation Type: select '''ADSL'''
# DSL Modulation Type: select '''ADSL'''
# ATM Configuration, enter...
# ATM Configuration, enter...
# VPI: '''0'''
#* VPI: '''0'''
# VCI: '''35'''
#* VCI: '''35'''
# WAN Service Setup, enter...
#* Connection Type: '''Bridge'''
# Click '''Save'''
 
[[File:Td-w9970_bridge3.png|699x699px|Configuring for Bridge Mode 3/3]]


[[File:Td-w9970_bridge3.png|800px|Configuring for Bridge Mode 3/3]]
Follow the instructions in [[#Manage Control|Manage Control]] to secure your modem.


# WAN Service Setup, enter...
= See Also =
# Connection Type: '''Bridge'''
{{Template:TD-W9970_Links}}
# Click '''Save'''


= See also =
*[[Modem Configuration]] - for a complete list of instructions for all NCF modems
*[[Modem Configuration]] - for a complete list of instructions for all NCF modems
*[[Modem Lights#TP-Link|About TP-Link Modem Lights]]
*[[Modem Lights#TP-Link|About TP-Link Modem Lights]]
*[http://www.ncf.ca/ncf/dsl/modem/TD-W9970_V1_UG.pdf TP-Link TD-W9970 manual]
*[http://www.ncf.ca/ncf/dsl/modem/TD-W9970_V1_UG.pdf TP-Link TD-W9970 manual]
<!-- *[https://www.ncf.ca/ncf/support/w/images/f/f8/Modem_Info_Pages_-_TP-Link_505n_v1.0.pdf NCF TP-Link TD-W9970 modem instruction sheet] need to do up a modem info page for TD-9970 -->
*[https://www.ncf.ca/ncf/support/w/images/8/8c/About_Your_TP-Link_TD-W9970.pdf About Your TP-Link TD-W9970]
*[[Changing WiFi Channels on TP-Link TD-W9970]]
*[[Changing WiFi Channels on TP-Link TD-W9970]]
*[[Dynamic DNS]]
*[[Dynamic DNS]]

Latest revision as of 16:26, 24 March 2021

TP Link TD-W9970
 TD-W9970 Front TD-W9970 Back

Sold from Jan 2016 to Oct 2017

The TP-Link TD-W9970 Modem Front
The TP-Link TD-W9970 Modem Back

The TP-Link TD-W9970 is for use on any service on networks using Bell's DSL infrastructure. To learn more about configuring your particular modem, consult the manual.

Routed

The TP-Link TD-W9970 modem router supports both ADSL and VDSL, and switches automatically to match the line it is connected to.

VDSL

Routed | VDSL | ADSL | DNS Fix | UPnP | Time | Manage Control | CWMP | Firewall ♦ Bridge | VDSL | ADSL ♦ See Also

Back to the Top

We will start with the mode used for VDSL connections.

If the modem is new, a user name of admin and password of admin will gain access to the modem configuration. If the modem is not new, it is recommended to reset the modem to the factory default settings by holding down the Reset/Wi-Fi button for 6 to 9 seconds before continuing to Quick Setup Step 1 below.

Quick Setup

1. Once you access the modem from your browser at http://192.168.1.1 and login (user name: admin and password: admin), click the Quick Setup link in the Menu on the left.

Then click Next on the Quick Setup-Start page.

Getting started

Region and Time Zone

Back to the Top

  1. Set Region to Canada
  2. Time Zone to (GMT-05:00) Eastern Time (US & Canada)
  3. Click Next

Step2

Auto Detection

Back to the Top

  1. Click on No, I want to configure The Internet Connection myself
  2. Click Next

Step3

DSL

Back to the Top

  1. ISP: Other
  2. L2 Interface Type: VDSL
  3. Enable VLAN ID: checked
  4. VLAN: 35
  5. Connection Type: PPPoE
  6. Click Next

Step4

PPPoE

Back to the Top

  1. User name: ab123@ncf.ca (where ab123 is your NCF ID)
  2. Password: •••••••• (where •••••••• is your NCF DSL Password)
  3. Confirm password: ••••••••
  4. Click Next

Step5

3G/4G

Back to the Top

  1. Click Next

Step6

Wireless

Back to the Top

IMPORTANT NOTE: The Quick Setup process will not set the Wireless Security to use WPA2 exclusively with AES-- this means more recent devices connecting to the device may warn of insufficient security when connecting over Wi-Fi. To avoid this, after completing the Quick Setup, access the Wireless settings for the device, and ensure only WPA2 is selected for the Security protocol, and AES for the encryption method. A selection of WPA/WPA2 and AES/TKIP is less secure and will cause newer device to issue warnings.

  1. Wireless: Enable
  2. Wireless Network Name (SSID): NCF_XXXX (where XXXX are the last 4 digits of the modem serial number)
  3. Channel: Auto
  4. Mode: 11n only
  5. Security: WPA2
  6. Password: DSL Password
  7. Click Next

Step7

Confirm

Back to the Top

  1. Verify all setting are as entered
  2. Click Next

Step8

Complete

Back to the Top

  1. Click Finish

Stay logged-in

  1. Click Network (left-hand menu, 4th link from top)
  2. Click WAN Settings

DSL WAN Interface

  1. Click on Action: Edit (entry with pppoe_ptm_35_1_d, right-hand side of table)

WAN Settings

Back to the Top

  1. WAN Service Setup, enter...
  2. Enable IPv6: Selected
  3. Click Advance
  4. Enable SPI Firewall: selected
  5. Enable IGMP Proxy: un-select
  6. Click Save

Wireless Settings

Back to the Top

  1. Click Wireless (in left-hand menu)
  2. Click Wireless Security
  3. Ensure WPA/WPA2 (Personal) is selected
  4. Authentication Type: WPA2-PSK
  5. Encryption: AES
  6. Click Save

ADSL

Routed | VDSL | ADSL | DNS Fix | UPnP | Time | Manage Control | CWMP | Firewall ♦ Bridge | VDSL | ADSL ♦ See Also

Back to the Top

Moving on now to add settings for ADSL.

Stay logged-in

  1. Click Network (left-hand menu, 4th link from top)
  2. Click WAN Settings

DSL WAN Interface

Back to the Top

  1. Click on Action: Delete (1st entry, right-hand side of table)
  2. Then click Add button

Adding ADSL2+ WAN Config 1/2

WAN Settings

Back to the Top

  1. DSL Modulation Type: ADSL
  2. ATM Configuration: VPI/VCI = 0/35
  3. WAN Service Setup
    1. Connection Type: PPPoE
    2. PPP Username: ab123@ncf.ca (where ab123 is your NCF ID)
    3. PPP Password: •••••••• (your NCF DSL Password)
    4. Confirm password: ••••••••
    5. Enable IPv4: selected
    6. Enable IPv6: select
  4. Click Advance
    1. Enable SPI Firewall: selected
    2. Enable IGMP Proxy: un-select
  5. Click Save

Adding ADSL2+ WAN Config 2/2

DNS Fix

Routed | VDSL | ADSL | DNS Fix | UPnP | Time | Manage Control | CWMP | Firewall ♦ Bridge | VDSL | ADSL ♦ See Also

Back to the Top

There is a known issue where the internal DNS server sometimes stop responding after swapping between ADSL and VDSL connections. To avoid this issue, we recommend hard-coding a public DNS server instead of using the internal one.

DHCP Settings

  1. DNS Server: 1.1.1.1
  2. Secondary DNS Server: 1.0.0.1

DNS Fix for TD-W9970

UPnP

Routed | VDSL | ADSL | DNS Fix | UPnP | Time | Manage Control | CWMP | Firewall ♦ Bridge | VDSL | ADSL ♦ See Also

Back to the Top

  1. Click on Forwarding (left-hand menu, near the middle)
  2. UPnP: de-select

TD-W9970 setup13.png

Time

Routed | VDSL | ADSL | DNS Fix | UPnP | Time | Manage Control | CWMP | Firewall ♦ Bridge | VDSL | ADSL ♦ See Also

Back to the Top

  1. Click on System Tools (left-hand menu, towards the bottom)
  2. Select Time Settings
  3. Time Zone: (GMT-05:00) Eastern Time (US & Canada)
  4. NTP Server 1: time.nrc.ca
  5. Enable DST: checked
  6. Modify DST Start: 2nd Sunday in March
  7. Modify DST End: 1st Sunday in November
  8. Click Save

Configuring Time Settings

Manage Control

Routed | VDSL | ADSL | DNS Fix | UPnP | Time | Manage Control | CWMP | Firewall ♦ Bridge | VDSL | ADSL ♦ See Also

Back to the Top

  1. Click on System Tools (left-hand menu, towards the bottom)
  2. Select Manage Control
  3. For the user admin we use the member's DSL Password – user name & password should not exceed 15 characters
  4. Enter it once and again below to confirm
  5. Ensure ICMP (Ping) is set to Local only (default setting)
  6. Click Save

Td-w9970 setup11.png

CWMP

Routed | VDSL | ADSL | DNS Fix | UPnP | Time | Manage Control | CWMP | Firewall ♦ Bridge | VDSL | ADSL ♦ See Also

Back to the Top

  1. Click on System Tools (left-hand menu, towards the bottom)
  2. Select CWMP Settings
  3. Ensure that CWMP is de-selected (default setting)
  4. Ensure that Inform is de-selected (default setting)
  5. Click Save

Firewall

Routed | VDSL | ADSL | DNS Fix | UPnP | Time | Manage Control | CWMP | Firewall ♦ Bridge | VDSL | ADSL ♦ See Also

Back to the Top

  1. Click Firewall in the left column
  2. Select Enable Firewall if it's not Enabled

Bridge

Routed | VDSL | ADSL | DNS Fix | UPnP | Time | Manage Control | CWMP | Firewall ♦ Bridge | VDSL | ADSL ♦ See Also

Back to the Top

Do this only if you prefer to use your own external router rather than the one built into your TP-Link unit.

  1. Connect power and turn on the modem with the button on the back.
  2. Connect an Ethernet LAN cable to one of the yellow rear ports
  3. In the browser's address bar, enter the IP address for the modem interface page: 192.168.1.1
  4. If the modem is fresh from the factory, use the default user name and password to gain access
    1. user: admin
    2. password: admin

If the modem was previously configured for someone, the password would be the previous user's DSL password. If it is unknown then do a reset to factory default, press the reset/Wi-Fi button on the back. Hold for 6 to 9 seconds to reset. The user name and password will now be as above.

VDSL

Routed | VDSL | ADSL | DNS Fix | UPnP | Time | Manage Control | CWMP | Firewall ♦ Bridge | VDSL | ADSL ♦ See Also

Back to the Top

  1. Click on Quick Setup.

DSL

Back to the Top

  1. ISP: Other
  2. L2 Interface Type: VDSL
  3. Enable VLAN ID: checked
  4. VLAN: 35
  5. Connection Type: Bridge
  6. Click Next

Configuring for Bridge Mode 1/4

Wireless

Back to the Top

  1. Wireless: Disable
  2. Click Next

Configuring for Bridge Mode 4/4

Confirm

Back to the Top

  1. Verify all setting are as entered
  2. Click Next

Configuring for Bridge Mode 2/4

Stay logged-in

  1. Click Network (left-hand menu, 4th link from top)
  2. Click WAN Settings
  3. On the DSL WAN Interface page click Add

ADSL

Routed | VDSL | ADSL | DNS Fix | UPnP | Time | Manage Control | CWMP | Firewall ♦ Bridge | VDSL | ADSL ♦ See Also

Back to the Top

WAN Settings

  1. DSL Modulation Type: select ADSL
  2. ATM Configuration, enter...
    • VPI: 0
    • VCI: 35
  3. WAN Service Setup, enter...
    • Connection Type: Bridge
  4. Click Save

Configuring for Bridge Mode 3/3

Follow the instructions in Manage Control to secure your modem.

See Also

Routed | VDSL | ADSL | DNS Fix | UPnP | Time | Manage Control | CWMP | Firewall ♦ Bridge | VDSL | ADSL ♦ See Also

Back to the Top

Retrieved from "https://help.ncf.ca/index.php?title=TP-Link_TD-W9970_Configuration&oldid=7413"