Difference between revisions of "SmartRG SR505n Firmware"
Jump to navigation
Jump to search
(Created page with "<div class="ncfrightbox w-25"> {{Template:SmartRG SR506n}} </div> '''Recommended Firmware Version: 2.6.2.6''' {{Template:Firmware Caution}} You can verify your firmware by...") |
|||
| Line 5: | Line 5: | ||
{{Template:Firmware Caution}} | {{Template:Firmware Caution}} | ||
You can verify your firmware by checking the software version on the Device Info page.[[File: | You can verify your firmware by checking the software version on the Device Info page. '''⚠Caution: Modems with firmware older than version 2.5.0.14 must be first upgraded to version 2.5.0.14 before upgrading to version 2.6.2.6. Failure to do so may cause functionality problems which will not be covered by the manufacturer's warranty.''' | ||
To request | [[File:SR505n-firmware-version.png|alt=SmartRG SR505n Firmware version check on Device Info Page|none|thumb|566x566px|SmartRG SR505n Firmware version check on Device Info Page]] | ||
To request firmware, email [[mailto:support@ncf.ca support@ncf.ca]]. To install this new firmware onto your modem perform the following steps: | |||
# Download the firmware file and save it to a location on your computer that you can find easily. | # Download the firmware file and save it to a location on your computer that you can find easily. | ||
# Open a web browser and go to the address http://192.168.1.1 | # Open a web browser and go to the address http://192.168.1.1 | ||
# Select '''Manage Gateway (Advanced)''' and log in (by default the username is admin and password | # Select '''Manage Gateway (Advanced)''' and log in (by default the username is admin and password is your dsl password as shown in [[#Getting_Started|Getting Started]] above) | ||
# Click on '''Management''' → '''Update Software''' | # Click on '''Management''' → '''Update Software''' | ||
# Click on '''Browse''' | # Click on '''Browse''' | ||
# Upload the firmware file that you downloaded in step 1. | # Upload the firmware file that you downloaded in step 1. | ||
# Click '''Update Software''' | # Click '''Update Software''' | ||
[[File: | [[File:SR505n-firmware-update.png|alt=SR505n firmware update|none|thumb|579x579px|SR505n firmware update]] | ||
'''Note:''' the modem will reboot once the new firmware has been uploaded. This process may take up to 15 minutes to resync (DSL light returns to solid green) and reconnect (the internet light starts blinking again). | '''Note:''' the modem will reboot once the new firmware has been uploaded. This process may take up to 15 minutes to resync (DSL light returns to solid green) and reconnect (the internet light starts blinking again). | ||
=See Also= | =See Also= | ||
Revision as of 14:55, 26 September 2021
SmartRG SR506n
Sold from Aug 2018 to July 2021
- Home
- Configuration from File
- Routed Configuration
- Bridge Configuration
- Firmware Check and Update
- Changing WiFi Channels on SmartRG modems
- Changing WiFi Name or Password on SmartRG modems
- Changing DNS Settings on SmartRG Modems
- Port Forwarding
- About your SmartRG SR506n
- SmartRG - Manual
- SmartRG - Data Sheet
- Highspeed Tips - SR505n Emulator (differs slightly)
Recommended Firmware Version: 2.6.2.6
SmartRG firmware update/s available to NCF members only. Firmware updates have been validated and tested against a custom configuration for NCF DSL members. Non-NCF requests will be disregarded.
Caution:
- We recommend that you only do firmware updates over an Ethernet connection and NOT via Wi-Fi.
- DO NOT power off the modem during a firmware update, as this will cause your modem become unresponsive (stuck in brick/recovery mode).
You can verify your firmware by checking the software version on the Device Info page. ⚠Caution: Modems with firmware older than version 2.5.0.14 must be first upgraded to version 2.5.0.14 before upgrading to version 2.6.2.6. Failure to do so may cause functionality problems which will not be covered by the manufacturer's warranty.
To request firmware, email [support@ncf.ca]. To install this new firmware onto your modem perform the following steps:
- Download the firmware file and save it to a location on your computer that you can find easily.
- Open a web browser and go to the address http://192.168.1.1
- Select Manage Gateway (Advanced) and log in (by default the username is admin and password is your dsl password as shown in Getting Started above)
- Click on Management → Update Software
- Click on Browse
- Upload the firmware file that you downloaded in step 1.
- Click Update Software
Note: the modem will reboot once the new firmware has been uploaded. This process may take up to 15 minutes to resync (DSL light returns to solid green) and reconnect (the internet light starts blinking again).
See Also
- Modem Configuration - Instructions for all NCF modems
- About SmartRG modem lights
- SmartRG SR505N Changing Wi-Fi Channels
- Dynamic DNS
- Port forwarding with the SmartRG SR505N