SmartRG SR506n

SmartRG SR506n

Sold from Aug 2018 to July 2021

• Home
• Configuration from File
• Routed Configuration
• Bridge Configuration
• Firmware Check and Update
• Changing WiFi Channels on SmartRG modems
• Changing WiFi Name or Password on SmartRG modems
• Changing DNS Settings on SmartRG Modems
• Port Forwarding
• About your SmartRG SR506n
• SmartRG - Manual
• SmartRG - Data Sheet
• Highspeed Tips - SR505n Emulator (differs slightly)

Preparation

Updated: 2018-08-29 Recommended Firmware Version: 2.6.1.6

The SmartRG SR506n modem router supports both ADSL mode and VDSL mode. Provided it is configured correctly, it can be switched between ADSL and VDSL plans without the owner having to buy a new modem or even reconfigure your existing one.

• Note: Fees for changing plans may still apply. Consult: DSL Rates

Before you start configuring the SmartRG SR506n, there are 4 things to check:

1. Firmware Check: Check if you're using older firmware and upgrade to the recommended firmware version. If you're unable to access the internet to request newer firmware, note that the screenshots shown and steps outlined may not align with what you see. Contact the support@ncf.ca for assistance if you run into problems.
2. Factory Settings and Standard Configuration: These instructions assume you're configuring SmartRG SR506n modem out of the box or after a factory reset. If the modem is not new, it is recommended to reset the modem to the factory defaults by holding down the reset button with a paper clip for ~10 seconds.
   • Also, these settings are our recommendations for most NCF members. To learn more about making custom changes to your particular modem, consult the manual.
3. Modem Installation - Configure over Ethernet: Consult the SmartRG SR506N modem instruction sheet (page 1) on how to set up the modem and connect to it over ethernet. We do not recommend configuring your modem over a WiFi connection.
4. Configurations Methods: The 2 main ways of configuring the SmartRG SR506n modem:
   • Using a custom configuration File: You can request a custom configuration file for your NCF DSL connection from support@ncf.ca.
   • Manually following configuration steps
5. Configuration Options:
   • Routed Operation with WiFi - Standard configuration for most members with SmartRG SR506n serving as both modem and WiFi router.
   • Routed Operation with separate WiFi Router - Recommended configuration for members with their own WiFi router. The modem will make the PPPoE authentication and both devices will negotiate DHCP.
   • Bridged Operation with separate WiFi Router - (Advanced) for members with their own routers and are knowledgeable about managing it themselves. The router with handle both authentication and DHCP.

Bridge Operation

Back to the Top

NCF Support is available to make configuring your SmartRG modem easier and to help you avoid potential mistakes. Here are simpler configuration options for your SmartRG modem:

1. You can request a custom configuration file for your NCF DSL connection from support@ncf.ca.
   • You may need an alternate means of accessing the internet to download the configuration file.
2. Call 613-721-1773 x0 to book a Modem Appointment.

If you prefer your own external router rather than the one built into your SmartRG unit, we recommend routed operation with a separate WiFi Router. However if you have networking expertise and are confident using the modem in bridge mode then take note of the following before configuring your SmartRG for Bridged operation:

1. Once you complete configuring your SmartRG modem for Bridged operation and disconnect from the modem, the Modem's Web Interface will become inaccessible and you may not be able to regain access to it until you reset the modem.
   • Backup Settings: It is particularly important to backup the Running Settings on your modem before and after you configure it.
   • To reset the modem: If you need to reset the modem, insert a paper-clip in the Reset hole on the back. Hold for 10 seconds to reset.
2. If you set up the modem for Bridge operation, then your router will need to be configured in PPPoE mode with your DSL username and password.

Checklist

Back to the Top

Steps to Configure SR506N for Bridge Operation

	Steps	Menu Navigation	Parameters
1	Log into Modem	http://192.168.1.1 → Manage Gateway (Advanced)	User Name: admin Password: admin
2	WAN Cleanup	Advanced Setup → WAN Service	Remove ppp0.1 from WAN Service Table
3	Enable ADSL	Advanced Setup → Layer2 Interface → ATM Interface	Add ATM: vpi:0 vci:35 DSL Latency: FAST and INTERLEAVED
4	Enable VDSL	Advanced Setup → Layers2 Interface → PTM Interface	Remove ptm0 with Path0 Add PTM: DSL Latency: FAST and INTERLEAVED
6	Configure ADSL	Advanced Setup → WAN Service	Add atm0/(4_0_35) Bridge (br_4_0_35)
7	Configure VDSL	Advanced Setup → WAN Service	Add ptm0/(4_1_1) Bridge(br_4_1_1.35) 802.1P Priority:1 802.1Q VLAN:35
9	WiFi	Wireless	Disable Wireless
11	Admin Password	Management → Access Controls → Passwords	Username: admin Old Password: admin (or whatever you set it to) New Password: your DSL password
12	Disable Support	Management → Accounts → Access Controls	Delete/Modify Account Select Support role Disable Update (at bottom)
13	Remote Access	Management → Management Server	TR-069 Client: Disable ACS URL: https://acs.ncf.ca
14	System Log	Management → System Log	Configure System Log System Log:Enable Log Level: Debugging Display Level: Error Mode: Local
16	Backup Settings	Management → Settings → Backup	Backup Running Settings Save backup file to computer

Images

• 

  SmartRG SR506n - Front

• 

  SmartRG SR506n - Back

• 

  SmartRG SR506n - bottom

• 

  SmartRG SR506n - Left Side

• 

  SmartRG SR506n - Angled

See Also

Back to the Top

• Modem Configuration - for a complete list of instructions for all NCF modems
• About SmartRG modem lights
• File:Changing_Wireless_Channels_on_SmartRG_SR505N.pdf SmartRG SR505N Changing WiFi Channels
• Dynamic DNS
• Port forwarding with the SmartRG SR505N