DSL Quick Configuration Info
VPI / VCI (ADSL)	0.35
VLAN (VDSL)	35
Protocol	PPPoE
DSL username	(eg. aa999@ncf.ca)
DSL Password	Starts with 'ncf' (not the same as your NCF Start Page login)

Modems are available for sale to NCF members only. If you don't require configuration, modem sales can be handled over-the-counter in the office.

You have several choices:

Current modems sold by NCF

SmartRG SR505N and SR506N Configuration - how to configure the current four Ethernet port plus "N" wireless modem NCF sold from September 2014 to present for 15 Mb/s service and faster

Older modems previously sold by NCF

TP-Link TD-W9970 Configuration - how to configure the current four Ethernet port plus "N" wireless modem NCF sold from January 2016 to October 2017 to for 15 Mb/s service and faster
TP-Link TD-8816 Configuration - how to configure the current single Ethernet port modem NCF sold from December 2011 to October 2017
Sagemcom 2864 Configuration - how to configure the current four Ethernet port plus "N" wireless modem NCF sold between November 2013 to August 2014 for 15 Mb/s service and faster
TP-Link TD-W8951ND Configuration - how to configure the current four Ethernet port plus "N" wireless modem NCF sold between November 2012 to January 2016
TP-Link TD-W8901G Configuration - how to configure the four Ethernet port plus "G" wireless modem NCF sold between December 2011 and October 2012
TP-Link TD-W8950ND Configuration - how to configure the four Ethernet port plus "N" wireless modem NCF sold between December 2011 and October 2012
TP-Link TD-W8961ND Configuration
SpeedTouch Configuration - how to configure the older SpeedTouch modems NCF sold until the fall of 2011

Unsupported Modems

Bell allows its DSL customers to either rent or buy their modems. Some of the modems become available as used modems. The modems will work well on the Bell lines used by NCF DSL members.

Configuration instructions for the Bell Home Hub 1000. The Bell Home Hub 1000 or Sagemcom FAST4350 is an ADSL/VDSL modem. As of 2017-05-05, the modem supports all of the DSL speeds available from NCF (i.e. from 6-0.8 to 50-10).

Bell Home Hub 2000

The Bell Home Hub 2000 or Sagemcom FAST5250 is an ADSL/VDSL modem. As of 2017-05-05, the modem supports all of the DSL speeds available from NCF (i.e. from 6-0.8 to 50-10).

Factory Reset and Logging in

It's best to congifure this modem from factory settings but that means that you existing internet connection will be lost(if your moving from another DSL provider to NCF).

1. Connect the modem to DSL connection and via Ehternet to the computer. Perform a factory reset by holding the reset button on the side of the modem down for 30 seconds. Wait for the Power light to flash 5 times and release the reset button.

After a factory reset,

Configuration server username is "Administrator"
Configuration server password is "admin"
Gateway and configuration server are 192.168.2.1
The firewall is enabled and properly configured
The modem will connect to ADSL or VDSL
The modem is not configured to authenticate for an NCF Internet connection
Wi-Fi is enabled with a default configuration that must be changed
WPS is enabled

2. Enter [192.168.2.1] into the address bar of your browser

Changing Internet/PPPoE Login Settings

3. After any successful login, the modem configuration server may ask if you want to use password recovery. Choose "No" because the Bell password recovery would only work for a Bell DSL customer.

4. At the Top Left of the Landing page, click on Fibe Internet.

The Status will say disconnected if there's currently no working internet/PPPoE configuration settings on the modem.

5. Click on the Settings button and enter the default password admin when prompted.

6. Enter your NCF DSL /PPPoE username and password into the Username and Password fields and click Save. It could take up to 30 seconds for the Status to change to Connected.

Your DSL/PPPoE username is in the format aa000@ncf.ca and your DSL/PPPoE password can be obtained from support@ncf.ca if you cannot locate it.

Changing WiFi Settings

7. After getting a successful internet authentication, go back to the home page and click on the WiFi settings button below the listed WiFi networks in the Manage my Wi-Fi section. If prompted for the admin password enter admin like before.

8. Select the Primary tab on the left of the page. Set the WiFi SSID and the WiFi password in the 2.4Ghz network. Click Save at the bottom of the page.

Keeping the same network name (SSID) for 2.4GHz and 5GHz wifi connections is okay so far as you understand the pros and cons. If you set diffferent network names you will be able to determine which works better on specific clients. However, we understand this involves additional post-configuration work that not all members are interested in or equipped for.

At this point, the modem will be ready for test on ADSL/VDSL (whatever connection you have) and also over wifi.

Change the Administrative Password

9. Return to the Home page and click on the Modem Settings link at the bottom of the page and enter the default password "admin" when prompted.

10. Click Change under the Password section of the Administrator Settings

11. Enter the Current Password admin, the new password and confirm the new password and select Save

NCF recommends using your DSL password as administrative password for your modem. If you choose to use something else, please make a note of it so your can remember it.

Testing on alternate DSL connection

This is usually only available or necessary the NCF office as many members only have on DSL connection at their premise.

After testing on ADSL, disconnect and unplug the modem, and then reconnect it with VDSL. The modem will probably assign a different IP address to the computer so, at the computer, you should disconnect and then reconnect the modem interface. You may also have to re-enter the DSL login password, but the DSL login ID will already be present.

At this point, the modem will be ready for test on VDSL.

External links

Harden your router/wireless router - good advice on modem setings

Modem Configuration

Contents