Difference between revisions of "Router Configuration"
m (→See also) |
|||
| (25 intermediate revisions by 5 users not shown) | |||
| Line 1: | Line 1: | ||
<div class="ncfrightbox"> {{Template:Modem Links}} </div> | |||
This page deals with configuring a wifi router to work with a DSL modem. | |||
==Router Configuration== | |||
When a separate router is used with your NCF modem, the typical setup is to put the modem into | When a separate router is used with your NCF modem, the typical setup is to put the modem into [[Modem Modes|Bridge Mode]] and have the router do the user authentication. The name of that authentication setting is called "PPPoE" (Point-to-Point Protocol over Ethernet). | ||
You should be able to configure your router by simply connecting the unit to your computer with an ethernet cable | You should be able to configure your router by simply connecting the unit to your computer with an ethernet cable and accessing the built-in configuration page though your web browser. The address for the user interface, to be entered in your browser's location bar, is often written on the bottom of the unit, or in the router's user manual. | ||
= | ==General router configuration information== | ||
Once you can edit the router's interface enter: | |||
[[ | #Under "Connection type" (or similar term) Select "PPPoE" | ||
#Under "Account Name", enter in your NCF ID (same format as ''ab123@ncf.ca'') | |||
#Under "Password", enter your [[DSL password]]. Enter it in again under "Verify Password" if required | |||
#Under "Service Name", check your router manual or leave it blank. | |||
[[ | ==How to configure some specific router models== | ||
*[[DLink Router Configuration]] | |||
*[[Apple Airport Router Configuration]] | |||
==Routers Reconfigured with Open Source Software== | |||
Some routers, like the LinkSys WRT-54G, may have been reconfiigured by replacing the orginal software with different software. The replacement software is normally Linux-based, and it may not be possible to set up the router by following the instructions in the original documentation. | |||
In such a case, try doing a "factory reset" by holding the reset button for 30 seconds or more, and possiblity turning the router off and holding the reset button again while turning the router on. | |||
Afer a sucessful factory reset, | |||
* the administrative user ID is likely to be "root" instead of something like "admin" or "Administrator" | |||
* the default password is likely to be blank instead of something like "password" | |||
==See also== | |||
*[[Special:Categories|DSL Help Categories]] | |||
*[[Modem Modes]] | |||
[[Category:DSL]] | |||
[[Category:Modems]] | |||
[[Category:Home Network]] | |||
Latest revision as of 17:50, 28 July 2018
This page deals with configuring a wifi router to work with a DSL modem.
Router Configuration
When a separate router is used with your NCF modem, the typical setup is to put the modem into Bridge Mode and have the router do the user authentication. The name of that authentication setting is called "PPPoE" (Point-to-Point Protocol over Ethernet).
You should be able to configure your router by simply connecting the unit to your computer with an ethernet cable and accessing the built-in configuration page though your web browser. The address for the user interface, to be entered in your browser's location bar, is often written on the bottom of the unit, or in the router's user manual.
General router configuration information
Once you can edit the router's interface enter:
- Under "Connection type" (or similar term) Select "PPPoE"
- Under "Account Name", enter in your NCF ID (same format as ab123@ncf.ca)
- Under "Password", enter your DSL password. Enter it in again under "Verify Password" if required
- Under "Service Name", check your router manual or leave it blank.
How to configure some specific router models
Routers Reconfigured with Open Source Software
Some routers, like the LinkSys WRT-54G, may have been reconfiigured by replacing the orginal software with different software. The replacement software is normally Linux-based, and it may not be possible to set up the router by following the instructions in the original documentation.
In such a case, try doing a "factory reset" by holding the reset button for 30 seconds or more, and possiblity turning the router off and holding the reset button again while turning the router on.
Afer a sucessful factory reset,
- the administrative user ID is likely to be "root" instead of something like "admin" or "Administrator"
- the default password is likely to be blank instead of something like "password"