Head blueLogoText.gif NCF HelpWiki
Help | StartPage

Difference between revisions of "Ovislink OV935WVA Routed Configuration"

From Support
Jump to navigation Jump to search
(Updating instructions to be easier to understand)
(Undo revision 8369 by Ga928 (talk))
Tag: Undo
 
(5 intermediate revisions by the same user not shown)
Line 23: Line 23:
|'''Advanced Setup'''
|'''Advanced Setup'''
'''→ WAN Service'''
'''→ WAN Service'''
|Remove everything from the '''WAN''' Service Table  
|Remove everything from the '''WAN''' Service Table by clicking the checkbox on the right for each entry,
then click the Remove button
|-
|-
|3
|3
Line 44: Line 45:
'''→ PTM Interface'''
'''→ PTM Interface'''
|
|
* Remove '''atm0''' from the table by clicking the checkbox on the  right, then click the '''Remove''' button
* Remove '''ptm0''' from the table by clicking the checkbox on the  right, then click the '''Remove''' button
* Click '''Add'''
* Click '''Add'''
* DSL Latency: Both checkboxes for '''FAST''' and '''INTERLEAVED'''  should be checked
* DSL Latency: Both checkboxes for '''FAST''' and '''INTERLEAVED'''  should be checked
Line 58: Line 59:
** PPPoE username: your DSL username (format: aa000@ncf.ca
** PPPoE username: your DSL username (format: aa000@ncf.ca
** PPPoE password: your DSL password
** PPPoE password: your DSL password
** Enable '''Firewall'''
** Check the box to the left for '''Enable IPv6 for this service'''
** Enable '''NAT'''
* Click '''Next''', then on each following page click '''Next''' until it  changes to '''Apply/Save'''. Then click '''Apply/Save'''  
* Click '''Next''', then on each following page click '''Next''' until it  changes to '''Apply/Save'''. Then click '''Apply/Save'''  
|-
|-
Line 67: Line 67:
'''→ WAN Service'''
'''→ WAN Service'''
|
|
* Click Add, then select '''atm0/(4_0_35)''', then click Next
* Click Add, then select '''ptm0/(4_1_1)''', then click Next
* On the '''WAN Service Configuration''' page:
* On the '''WAN Service Configuration''' page:
** Change the setting of 802.1P Priority from '''-1''' to '''1'''
** Change the setting of 802.1P Priority from '''-1''' to '''1'''
Line 74: Line 74:
** PPPoE username: your DSL username (format: aa000@ncf.ca)
** PPPoE username: your DSL username (format: aa000@ncf.ca)
** PPPoE password: your DSL password
** PPPoE password: your DSL password
** Enable '''Firewall'''
** Check the box to the left for '''Enable IPv6 for this service'''
** Enable '''NAT'''
* Click '''Next''', then on each following page click '''Next''' until it  changes to '''Apply/Save'''. Then click '''Apply/Save'''  
* Click '''Next''', then on each following page click '''Next''' until it  changes to '''Apply/Save'''. Then click '''Apply/Save'''  
|-
|-
Line 88: Line 87:
|'''Wireless'''
|'''Wireless'''
'''→ 5 GHz Band'''
'''→ 5 GHz Band'''
|SSID (WiFi Name) to format '''NCF_XXXX,''' where XXXX  
|SSID (WiFi Name) to format '''NCF_XXXX,''' where XXXX is the last 4 digits of your modem's serial number
is the last 4 digits of your modem's serial number
|-
|-
|9
|9
Line 108: Line 106:
|'''Wireless'''
|'''Wireless'''
'''→ 2.4 GHz Band'''
'''→ 2.4 GHz Band'''
|SSID (WiFi Name) to format '''NCF_XXXX,''' where XXXX  
|SSID (WiFi Name) to format '''NCF_XXXX,''' where XXXX is the last 4 digits of your modem's serial number
is the last 4 digits of your modem's serial number
|-
|-
|11
|11

Latest revision as of 14:47, 30 January 2025

Ovislink OV935WVA
 Ovislink Front Ovislink Back

with WiFi

NCF Support is available to make configuring your OvisLink modem easier and to help you avoid potential mistakes. Here are simpler configuration options for your OvisLink modem. All settings in your modem not mentioned in these instructions can be ignored.

  1. You can request a custom configuration file for your NCF DSL connection from support@ncf.ca.
  2. Call 613-721-1773 x0 to book a Modem Appointment.
Steps to Configure OvisLink for Routed Operation
Steps Menu Navigation Parameters
1 Log into Modem http://192.168.1.1 User Name: admin

Password: admin

2 WAN Cleanup Advanced Setup

→ WAN Service

Remove everything from the WAN Service Table by clicking the checkbox on the right for each entry,

then click the Remove button

3 Enable ADSL Advanced Setup

→ Layer2 Interface

→ ATM Interface

  • Remove atm0 from the table by clicking the checkbox on the right, then click the Remove button
  • Click Add
  • Edit VPI and VCI. VPI should be 0, VCI should be 35
  • DSL Latency: Both checkboxes for FAST and INTERLEAVED should be checked
4 Enable VDSL Advanced Setup

→ Layer2 Interface

→ PTM Interface

  • Remove ptm0 from the table by clicking the checkbox on the right, then click the Remove button
  • Click Add
  • DSL Latency: Both checkboxes for FAST and INTERLEAVED should be checked
5 Configure ADSL Advanced Setup

→ WAN Service

  • Click Add, then select atm0/(4_0_35), then click Next
  • On the WAN Service Configuration page, click Next
  • On the PPP Username and Password page:
    • PPPoE username: your DSL username (format: aa000@ncf.ca
    • PPPoE password: your DSL password
    • Check the box to the left for Enable IPv6 for this service
  • Click Next, then on each following page click Next until it changes to Apply/Save. Then click Apply/Save
6 Configure VDSL Advanced Setup

→ WAN Service

  • Click Add, then select ptm0/(4_1_1), then click Next
  • On the WAN Service Configuration page:
    • Change the setting of 802.1P Priority from -1 to 1
    • Change the setting of 802.1Q VLAN from -1 to 35
  • On the PPP Username and Password page:
    • PPPoE username: your DSL username (format: aa000@ncf.ca)
    • PPPoE password: your DSL password
    • Check the box to the left for Enable IPv6 for this service
  • Click Next, then on each following page click Next until it changes to Apply/Save. Then click Apply/Save
7 UPnP Advanced Setup

→ UPnP

Disable uPnP
8 WiFi 5GHz Name Wireless

→ 5 GHz Band

SSID (WiFi Name) to format NCF_XXXX, where XXXX is the last 4 digits of your modem's serial number
9 WiFi 5 GHz Security Wireless

→ 5 GHz Band

→ Security

  • Disable WPS
  • Network Authentication to WPA2-PSK
  • WPA Passphrase : your DSL password
  • WPA Encryption : AES
10 WiFi 2.4 GHz Name Wireless

→ 2.4 GHz Band

SSID (WiFi Name) to format NCF_XXXX, where XXXX is the last 4 digits of your modem's serial number
11 WiFi 2.4 GHz Security Wireless

→ 2.4 GHz Band

→ Security

  • Disable WPS
  • Network Authentication to WPA2-PSK
  • WPA Passphrase : your DSL password
  • WPA Encryption : AES
12 Admin Password Management

→ Access Controls

→ Passwords

  • Username: admin
  • New Username: admin
  • Old Password: admin (or whatever you set it to)
  • New Password: your DSL password
13 Remote Access Management

→ TR-069 Client

  • Disable Inform
14 System Log Management

→ System Log

→ Configure System Log

Configuration:
  • Log:Enable
  • Log Level: Debugging
  • Display Level: Error
  • Mode: Local
15 Internet Time Management

→ Internet Time

Time settings:
  • Automatically synchronize with Internet time servers: Enable
  • First NTP time server: Other, then in the textbox to the right, put time.nrc.ca
  • Time Zone: (GMT - 5:00) Eastern Time
16 Backup Settings Management

→ Settings

→ Backup

Settings -Backup
  • Backup Settings

with separate WiFi Router

NCF Support is available to make configuring your OvisLink modem easier and to help you avoid potential mistakes. Here are simpler configuration options for your OvisLink modem:

  1. You can request a custom configuration file for your NCF DSL connection from support@ncf.ca. You may need an alternate means of accessing the internet to download the configuration file.
  2. Call 613-721-1773 x0 to book a Modem Appointment.

Configure your modem for Routed Operation

If you have a router, we recommend the following configuration steps:  

  1. Follow the configuration steps outline for Routed Operation with WiFi and make the following changes:
    • Under Wireless, Uncheck the Enable Wireless Option
    • Click Apply/Save

Router configuration

2. On your router, set the Connection Mode or Type to Automatic IP, Automatic DHCP or Dynamic IP mode

See Also

Back to the Top

Retrieved from "https://help.ncf.ca/index.php?title=Ovislink_OV935WVA_Routed_Configuration&oldid=8370"